22RE Parts - Pirate4x4.Com : 4x4 and Off-Road Forum

ToyotaJeep · 10-24-2004, 08:39 PM

I have several parts and pieces off of a various 22RE's

Here's a listing:

Exhaust Manifold with o2 sensor: $20.00

Exhaust head shields (2) $15.00 each

One complete upper and lower intake straight inlet (90's style) - $45.00

One complete upper and lower intake angled inlet - $45.00

Throttle Bodys (2) $20.00 each

Fuel rail assembly $15.00

Shipping is available on all items at the buyers expense.

No warranty on parts, make sure they're what you need prior to purchase

Location: Klamath Falls, Oregon

Contact: radjad@kfalls.net

It's best to email me.

ToyotaJeep · 10-27-2004, 05:54 AM

Ttt

jekbrown · 10-27-2004, 10:12 AM

whats wrong, specifically, with the complete 22re? Im looking for a rebuildable toy motor for my buggy...

j

ToyotaJeep · 10-27-2004, 06:47 PM

It has been rebuilt a few times and it is .040 over I believe. The cylinders look good etc. but I believe that it is now unboreable. The crank is good, and the head needs to be gone through. I pulled it out of my running 85 runner.

Send me an email at the following address and I can get more specific.

radjad@kfalls.net

ToyotaJeep · 10-31-2004, 10:55 AM

TTT - I am going to the Grants Pass / Medford Area on the 4th of November and can deliver.

Trades???

Thanks

porterwagner · 10-31-2004, 09:28 PM

hey do you have an ac bracket/idler pulley for it?? what year engine is it? maybe you have the vaccuum line from the as read valve going to the vsv. i need the vsv piece that mounts on the engine, it has two vacuum lines. thanks. Torey

ToyotaJeep · 10-31-2004, 09:48 PM

I do have the AC brackets off of what I believe was a 86 EFI rig. As far as the vacuum VSV piece, if you could send me a pic of what you need I can look. It attaches to the intake, correct?

BTW - You don't actually run 5.71's do you? Just wondering, I do.

porterwagner · 11-01-2004, 09:15 PM

Well for the time being i'm holding off on buying the brackets, and possibly the VSV stuff as well, being that you're from colorado and i don't know about shipping on that stuff. Im still searching local, but i will keep you in mind if nothing falls through, because i will have to get it running eventually, as for the picture. i'll try to post it up on here. I don't know if an 86er has it. I do have a picture of the part that i need, but i was looking in my book and the 86 doesn't even have an AS Read valve that connects to a VSV on top of the engine. There is quite a few differences. But once again thanks. and a big HELL YEAH i run 5.71s!!!!!! 5.71's are the shi*!!! They mob everywhere.

Total Distorsion · 11-01-2004, 09:45 PM

Coil/Ignitor?

ToyotaJeep · 11-02-2004, 06:40 PM

In reply to Porterwagner, I actually live up the road from you in southern Oregon. I do ship, and it isn't too bad if you keep it light. For instance, shipping a 45 lbs. flywheel to Texas came to approximately $25.00. Brackets and other stuff should be substantially less.

I don't have any spare coils and ignitors at this time.

Thanks for the interest. ROB

porterwagner · 11-03-2004, 07:38 AM

heres a picture of the bracket and pulley that i need. hopefully it works

porterwagner · 11-03-2004, 07:40 AM

theres like 3 differnt kind of brackets as well. this is the one i need because it is the one without a smog pump. so.... if you got it, that would be great. then we could work something out. thanks, Torey

ToyotaJeep · 11-04-2004, 09:07 PM

I'm quite certain I have what you're looking for. It came off of an FI engine I had 9 years ago!!

Send me an email at my home address and I'll send you some pictures later this weekend.

Thanks

Email: radjad@kfalls.net

porterwagner · 11-05-2004, 03:53 PM

e mailed you

ToyotaJeep · 11-05-2004, 07:11 PM

Emailed you back. I should be able to get you th information you need by tomorrow night.

Thanks

porterwagner · 11-07-2004, 06:12 PM

i don't need the brackets anymore. but the VSV would be sweet.

Izeloz · 11-07-2004, 06:57 PM

Do you have a newer plenum/intake? I have an '88 and would like to upgrade it to a straighter 90's type version.

ToyotaJeep · 11-16-2004, 10:09 PM

Yes, I have both styles of intakes.

Parts are all OBO within reason.

ToyotaJeep · 11-28-2004, 08:23 AM

Ttt

ToyotaJeep · 12-05-2004, 08:44 AM

OBO -don't need it

ToyotaJeep · 01-02-2005, 06:00 PM

It's all still here. Please make a reasonable offer and take it away.

Thanks

ToyotaJeep · 01-10-2005, 08:04 PM

Ttt

ToyotaJeep · 01-16-2005, 08:49 AM

These parts are still in the way.

Move em out.

Arnold · 01-16-2005, 09:45 AM

PM'ed ya.

ToyotaJeep · 01-16-2005, 10:23 AM

I sent you a PM in return. Sorry I couldn't help.

10-24-2004, 08:39 PM	#1 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	22RE Parts I have several parts and pieces off of a various 22RE's Here's a listing: Exhaust Manifold with o2 sensor: $20.00 Exhaust head shields (2) $15.00 each One complete upper and lower intake straight inlet (90's style) - $45.00 One complete upper and lower intake angled inlet - $45.00 Throttle Bodys (2) $20.00 each Fuel rail assembly $15.00 Shipping is available on all items at the buyers expense. No warranty on parts, make sure they're what you need prior to purchase Location: Klamath Falls, Oregon Contact: radjad@kfalls.net It's best to email me. Last edited by ToyotaJeep; 05-13-2005 at 06:27 AM.

10-27-2004, 10:12 AM	#3 (permalink)
jekbrown Registered User Join Date: Jan 2002 Member # 9070 Location: Vancouver, WA, USA, Earth Posts: 1,046	whats wrong, specifically, with the complete 22re? Im looking for a rebuildable toy motor for my buggy... j __________________ Leftists have killed 100,000,000+ people... still think its a good idea? [url=http://community.webshots.com/user/jekbrown]my 85 K5[/url]

10-31-2004, 09:28 PM	#6 (permalink)
porterwagner Registered User Join Date: Mar 2003 Member # 17544 Location: PARADISE norcal Posts: 1,187	hey do you have an ac bracket/idler pulley for it?? what year engine is it? maybe you have the vaccuum line from the as read valve going to the vsv. i need the vsv piece that mounts on the engine, it has two vacuum lines. thanks. Torey __________________ 1990 Toyota EX cab 22RE Dana 44 Front Alloys, T-100 Detroit rear. Duals 4.7s. 5.29s 5.38s This combo works Friends Of the High Lakes Cal4wheel BRC Tread Lightly

11-01-2004, 09:15 PM	#8 (permalink)
porterwagner Registered User Join Date: Mar 2003 Member # 17544 Location: PARADISE norcal Posts: 1,187	Well for the time being i'm holding off on buying the brackets, and possibly the VSV stuff as well, being that you're from colorado and i don't know about shipping on that stuff. Im still searching local, but i will keep you in mind if nothing falls through, because i will have to get it running eventually, as for the picture. i'll try to post it up on here. I don't know if an 86er has it. I do have a picture of the part that i need, but i was looking in my book and the 86 doesn't even have an AS Read valve that connects to a VSV on top of the engine. There is quite a few differences. But once again thanks. and a big HELL YEAH i run 5.71s!!!!!! 5.71's are the shi*!!! They mob everywhere. __________________ 1990 Toyota EX cab 22RE Dana 44 Front Alloys, T-100 Detroit rear. Duals 4.7s. 5.29s 5.38s This combo works Friends Of the High Lakes Cal4wheel BRC Tread Lightly

11-01-2004, 09:45 PM	#9 (permalink)
Total Distorsion Registered User Join Date: Jul 2001 Member # 5653 Location: Citrus Heights CA Posts: 1,479	Coil/Ignitor? __________________ Miller Metalworks

10-27-2004, 05:54 AM	#2 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	Ttt

10-27-2004, 06:47 PM	#4 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	It has been rebuilt a few times and it is .040 over I believe. The cylinders look good etc. but I believe that it is now unboreable. The crank is good, and the head needs to be gone through. I pulled it out of my running 85 runner. Send me an email at the following address and I can get more specific. radjad@kfalls.net

10-31-2004, 10:55 AM	#5 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	TTT - I am going to the Grants Pass / Medford Area on the 4th of November and can deliver. Trades??? Thanks

10-31-2004, 09:48 PM	#7 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	I do have the AC brackets off of what I believe was a 86 EFI rig. As far as the vacuum VSV piece, if you could send me a pic of what you need I can look. It attaches to the intake, correct? BTW - You don't actually run 5.71's do you? Just wondering, I do.

11-02-2004, 06:40 PM	#10 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	In reply to Porterwagner, I actually live up the road from you in southern Oregon. I do ship, and it isn't too bad if you keep it light. For instance, shipping a 45 lbs. flywheel to Texas came to approximately $25.00. Brackets and other stuff should be substantially less. I don't have any spare coils and ignitors at this time. Thanks for the interest. ROB

11-03-2004, 07:38 AM	#11 (permalink)
porterwagner Registered User Join Date: Mar 2003 Member # 17544 Location: PARADISE norcal Posts: 1,187	heres a picture of the bracket and pulley that i need. hopefully it works Attached Images __________________ 1990 Toyota EX cab 22RE Dana 44 Front Alloys, T-100 Detroit rear. Duals 4.7s. 5.29s 5.38s This combo works Friends Of the High Lakes Cal4wheel BRC Tread Lightly

11-03-2004, 07:40 AM	#12 (permalink)
porterwagner Registered User Join Date: Mar 2003 Member # 17544 Location: PARADISE norcal Posts: 1,187	theres like 3 differnt kind of brackets as well. this is the one i need because it is the one without a smog pump. so.... if you got it, that would be great. then we could work something out. thanks, Torey __________________ 1990 Toyota EX cab 22RE Dana 44 Front Alloys, T-100 Detroit rear. Duals 4.7s. 5.29s 5.38s This combo works Friends Of the High Lakes Cal4wheel BRC Tread Lightly

11-04-2004, 09:07 PM	#13 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	I'm quite certain I have what you're looking for. It came off of an FI engine I had 9 years ago!! Send me an email at my home address and I'll send you some pictures later this weekend. Thanks Email: radjad@kfalls.net

11-05-2004, 03:53 PM	#14 (permalink)
porterwagner Registered User Join Date: Mar 2003 Member # 17544 Location: PARADISE norcal Posts: 1,187	e mailed you __________________ 1990 Toyota EX cab 22RE Dana 44 Front Alloys, T-100 Detroit rear. Duals 4.7s. 5.29s 5.38s This combo works Friends Of the High Lakes Cal4wheel BRC Tread Lightly

11-05-2004, 07:11 PM	#15 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	Emailed you back. I should be able to get you th information you need by tomorrow night. Thanks

11-07-2004, 06:12 PM	#16 (permalink)
porterwagner Registered User Join Date: Mar 2003 Member # 17544 Location: PARADISE norcal Posts: 1,187	i don't need the brackets anymore. but the VSV would be sweet. __________________ 1990 Toyota EX cab 22RE Dana 44 Front Alloys, T-100 Detroit rear. Duals 4.7s. 5.29s 5.38s This combo works Friends Of the High Lakes Cal4wheel BRC Tread Lightly

11-07-2004, 06:57 PM	#17 (permalink)
Izeloz Registered User Join Date: Apr 2004 Member # 30087 Location: Utah Posts: 1,422	Do you have a newer plenum/intake? I have an '88 and would like to upgrade it to a straighter 90's type version.

11-16-2004, 10:09 PM	#18 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	Yes, I have both styles of intakes. Parts are all OBO within reason.

11-28-2004, 08:23 AM	#19 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	Ttt

12-05-2004, 08:44 AM	#20 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	OBO -don't need it

01-02-2005, 06:00 PM	#21 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	It's all still here. Please make a reasonable offer and take it away. Thanks

01-10-2005, 08:04 PM	#22 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	Ttt

01-16-2005, 08:49 AM	#23 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	These parts are still in the way. Move em out.

01-16-2005, 09:45 AM	#24 (permalink)
Arnold Registered User Join Date: Jul 2000 Member # 1246 Location: Granite Falls, WA Posts: 2,106	PM'ed ya.

01-16-2005, 10:23 AM	#25 (permalink)
ToyotaJeep Registered User Join Date: Jun 2000 Member # 1056 Posts: 3,828	I sent you a PM in return. Sorry I couldn't help.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode