ford fe445 - Pirate4x4.Com : 4x4 and Off-Road Forum

snewton · 02-16-2009, 11:39 AM

ford fe motor was a 390 now bored and stroked to a 445ci. edelbrock aluminum heads. new edelbrock aluminum water pump. shaft roller rockers. new milodon rear sump oil pan new edelbrock performer intake manifold.complete and ready for the dyno.in the ballpark of 550 to 600 hp on pump gas.$7000 (626) 833 6702 ask for steve

snewton · 02-18-2009, 12:49 PM

bump

PERFORMANCE · 02-18-2009, 01:03 PM

Who built this monster??

Lord Orange · 02-18-2009, 01:13 PM

what is the compression ratio?

snewton · 02-18-2009, 09:03 PM

the compression ratio is right around 10 to 10.5 to 1.motor was built to run pump gas no problem!

snewton · 02-20-2009, 12:18 AM

snewton · 02-22-2009, 10:50 AM

bump

snewton · 02-25-2009, 10:46 AM

top

snewton · 03-02-2009, 04:50 PM

ttt

snewton · 03-05-2009, 11:02 PM

make offers, must go!

woods · 03-06-2009, 06:20 AM

Might want to try here

http://www.clubhotrod.com/forums/forumdisplay.php?f=31

Or here

http://www.fordvehicles.com/trucks/f...1033&205363816

Not too many wheelers want to run this engine.
I might have jumped on it a few years ago when I was needing a good FE engine
There was much better FE site that I was a member of but can't find it right now.
Good luck

snewton · 03-09-2009, 10:58 PM

bump

snewton · 03-13-2009, 07:56 PM

top

02-16-2009, 11:39 AM	#1 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73	ford fe445 ford fe motor was a 390 now bored and stroked to a 445ci. edelbrock aluminum heads. new edelbrock aluminum water pump. shaft roller rockers. new milodon rear sump oil pan new edelbrock performer intake manifold.complete and ready for the dyno.in the ballpark of 550 to 600 hp on pump gas.$7000 (626) 833 6702 ask for steve

02-18-2009, 01:03 PM	#3 (permalink)
PERFORMANCE Registered User Join Date: Dec 2003 Member # 25540 Location: HESPERIA CA Posts: 387	Who built this monster?? __________________ -FIX IT FASTER- 73 COMMANDO 1-TONS AND 40'S

02-18-2009, 01:13 PM	#4 (permalink)
Lord Orange Registered User Join Date: Dec 2001 Member # 9001 Location: Suisun Ca Posts: 3,966	what is the compression ratio? __________________ [URL="http://www.pirate4x4.com/forum/showthread.php?t=530797"]Don't be the nice guy anymore[/URL]

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-18-2009, 12:49 PM	#2 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73	bump

02-18-2009, 09:03 PM	#5 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73	the compression ratio is right around 10 to 10.5 to 1.motor was built to run pump gas no problem!

02-20-2009, 12:18 AM	#6 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73

02-22-2009, 10:50 AM	#7 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73	bump

02-25-2009, 10:46 AM	#8 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73	top

03-02-2009, 04:50 PM	#9 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73	ttt

03-05-2009, 11:02 PM	#10 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73	make offers, must go!

03-06-2009, 06:20 AM	#11 (permalink)
woods Rock God Join Date: Jan 2002 Member # 9233 Location: Hollister, Ca. Posts: 1,251	Might want to try here http://www.clubhotrod.com/forums/forumdisplay.php?f=31 Or here http://www.fordvehicles.com/trucks/f...1033&205363816 Not too many wheelers want to run this engine. I might have jumped on it a few years ago when I was needing a good FE engine There was much better FE site that I was a member of but can't find it right now. Good luck

03-09-2009, 10:58 PM	#12 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73	bump

03-13-2009, 07:56 PM	#13 (permalink)
snewton Registered User Join Date: Feb 2009 Member # 129570 Posts: 73	top