Does Dana/Spicer Sell Axles? - Pirate4x4.Com : 4x4 and Off-Road Forum

Voltron · 08-27-2001, 11:27 PM

Ok, stupid Subject line.

What I'm wondering is where all the guys like Currie and anyone else get their D44's and D60's. Does Dana send them the parts or are they just liscenced to make them?

For example, there are no vehicles out there still in production with YJ width D44's or 60's. However, you can go out and buy one from any number of shops...

What's the deal???

Leader · 08-28-2001, 10:01 AM

I think Sunray takes factory ones and has them sent out to be cut and resplined..Inland truck parts around here can order a new dana axle if you have the build numbers off the axle housing..Are you talking about the whole axle or just the innerds? (just thought about it)

Voltron · 08-28-2001, 06:29 PM

I'm talking about the casting and the tubes mostly. Pretty sure the Terra 60R is home made with the tubes pressed in, but what about the rest???

Do they have their own castings and tubes or do they get them from like Dodge and cut them....????

Eric · 08-29-2001, 07:22 AM

I think Dynatrac has Dana make their castings for them.

BillaVista · 08-29-2001, 05:00 PM

Well that's a pretty big trade secret, and I don't think you'll likely find an answer - for the very reason you're asking - why pay the middleman??

Or you'll find whoever casts them won't sell retail / small quantaties.

I poked around this a bit a while back - I don;t think any of the common shops have Dana do the castings - the quantaties are just far too small. But someone casts them just nobody's saying who

Don A · 08-30-2001, 01:54 PM

I saw a note from Phil Jenson saying that he had a contact at Dana/Spicer to buy stock D44 TJ axles. You may be able to buy other parts as well. Look at the archives of the TJ Email list. Send mail to the following for info and FAQ for this list:
jeep-tj-info@mailinglists.org
jeep-tj-faq@mailinglists.org

Good Luck,

[ 08-30-2001: Message edited by: Don A ]

[ 08-30-2001: Message edited by: Don A ]

Don A · 08-30-2001, 06:38 PM

Quote:

Originally posted by Don A:
I saw a note from Phil Jenson saying that he had a contact at Dana/Spicer to buy stock D44 TJ axles. You may be able to buy other parts as well. Look at the archives of the TJ Email list. Send mail to the following for info and FAQ for this list:
jeep-tj-info@mailinglists.org
jeep-tj-faq@mailinglists.org

Phil just posted some pictures. Check them out.

-----------------------------------
From: Phil Jensen - pjensen@jssinc.on.ca
Subject: My new rear TJ axle arrived from Drivetrain Direct.

Note: These will be avaiable soon for purchase for a fraction of the
cost of a D60 from that other place ;-)
http://jeep-club.irtech.com/Phils_Mods/corp14.jpg
http://jeep-club.irtech.com/Phils_Mods/Corp14diff.jpg
http://jeep-club.irtech.com/Phils_Mo...p14floater.jpg
http://jeep-club.irtech.com/Phils_Mods/corp14brake1.jpg

Contact me directly if you want more info on a Corp14 axle for your Jeep.

Phil

[ 08-31-2001: Message edited by: Don A ]

Voltron · 08-30-2001, 11:40 PM

Don, I tried the links, but couldnt' find anything pertinent to the whole Dana Spicer thing in the archives. (didn't look that hard though)

That thing is sweet!!!! Who is this Phil guy, and what's his deal???

I want one. (I want the $$$ to pay for it too...)

Don A · 08-31-2001, 12:47 PM

Quote:

Originally posted by wrangler40:
Don, I tried the links, but couldnt' find anything pertinent to the whole Dana Spicer thing in the archives. (didn't look that hard though)

That thing is sweet!!!! Who is this Phil guy, and what's his deal???

I want one. (I want the $$$ to pay for it too...)

Yea, it does look beefy.

Phil has a friend that works at one of those parts places (Dana/Spicer/Drivetrain) and has done some "deals" in the past on buying TJ stuff (axle shafts, etc) for much less $$ than other parts houses. I don't know him and I have never been part of one of his "deals," I'm just passing along some info I saw on a Email list. If you are interested, send him an Email.

Good luck,

--Don

BadAZYj · 08-31-2001, 01:25 PM

What is Phil's email address?

Don A · 08-31-2001, 02:17 PM

Quote:

Originally posted by Scott Maiden:
What is Phil's email address?

The BBS program hid it because it had "<" and ">" around it. Phils address is pjensen@jssinc.on.ca

FWIW, I edited the above post so it now shows up.

08-27-2001, 11:27 PM	#1 (permalink)
Voltron Registered User Join Date: Jan 2001 Member # 2858 Location: San Diego, CA Posts: 307	Does Dana/Spicer Sell Axles? Ok, stupid Subject line. What I'm wondering is where all the guys like Currie and anyone else get their D44's and D60's. Does Dana send them the parts or are they just liscenced to make them? For example, there are no vehicles out there still in production with YJ width D44's or 60's. However, you can go out and buy one from any number of shops... What's the deal??? __________________ [i]If life gives you lemons, make lemonade. If life gives you crap, don't make a beverage out of it[/i] 85 4Runner, [B]STOLEN JUNE '03[/B] 87 4Runner, 33's, 4.88's TRD e-locker rear, [b]I[/b]nexpensive[b]F[/b]ront[b]S[/b]uspension [B]STOLEN ON 10/17/04[/B]

08-28-2001, 10:01 AM	#2 (permalink)
Leader Registered User Join Date: Jun 2001 Member # 5091 Location: Decatur TX. Posts: 51	I think Sunray takes factory ones and has them sent out to be cut and resplined..Inland truck parts around here can order a new dana axle if you have the build numbers off the axle housing..Are you talking about the whole axle or just the innerds? (just thought about it) __________________ It's as close to a 1ton as you can get and still look like a jeep!!

08-28-2001, 06:29 PM	#3 (permalink)
Voltron Registered User Join Date: Jan 2001 Member # 2858 Location: San Diego, CA Posts: 307	I'm talking about the casting and the tubes mostly. Pretty sure the Terra 60R is home made with the tubes pressed in, but what about the rest??? Do they have their own castings and tubes or do they get them from like Dodge and cut them....???? __________________ [i]If life gives you lemons, make lemonade. If life gives you crap, don't make a beverage out of it[/i] 85 4Runner, [B]STOLEN JUNE '03[/B] 87 4Runner, 33's, 4.88's TRD e-locker rear, [b]I[/b]nexpensive[b]F[/b]ront[b]S[/b]uspension [B]STOLEN ON 10/17/04[/B]

08-29-2001, 07:22 AM	#4 (permalink)
Eric Registered User Join Date: Feb 2000 Member # 39 Location: San Martin, CA Posts: 3,266	I think Dynatrac has Dana make their castings for them. __________________ Eric Parts for Sale --> D44 shafts, 6 lug rims, air tank

08-30-2001, 11:40 PM	#8 (permalink)
Voltron Registered User Join Date: Jan 2001 Member # 2858 Location: San Diego, CA Posts: 307	Don, I tried the links, but couldnt' find anything pertinent to the whole Dana Spicer thing in the archives. (didn't look that hard though) That thing is sweet!!!! Who is this Phil guy, and what's his deal??? I want one. (I want the $$$ to pay for it too...) __________________ [i]If life gives you lemons, make lemonade. If life gives you crap, don't make a beverage out of it[/i] 85 4Runner, [B]STOLEN JUNE '03[/B] 87 4Runner, 33's, 4.88's TRD e-locker rear, [b]I[/b]nexpensive[b]F[/b]ront[b]S[/b]uspension [B]STOLEN ON 10/17/04[/B]

08-29-2001, 05:00 PM	#5 (permalink)
BillaVista Registered User Join Date: Mar 2001 Member # 3547 Location: Ottawa, Canada Posts: 6,719	Well that's a pretty big trade secret, and I don't think you'll likely find an answer - for the very reason you're asking - why pay the middleman?? Or you'll find whoever casts them won't sell retail / small quantaties. I poked around this a bit a while back - I don;t think any of the common shops have Dana do the castings - the quantaties are just far too small. But someone casts them just nobody's saying who

08-30-2001, 01:54 PM	#6 (permalink)
Don A Registered User Join Date: Sep 2000 Member # 1835 Location: Bay Area, CA Posts: 166	I saw a note from Phil Jenson saying that he had a contact at Dana/Spicer to buy stock D44 TJ axles. You may be able to buy other parts as well. Look at the archives of the TJ Email list. Send mail to the following for info and FAQ for this list: jeep-tj-info@mailinglists.org jeep-tj-faq@mailinglists.org Good Luck, [ 08-30-2001: Message edited by: Don A ] [ 08-30-2001: Message edited by: Don A ]

08-31-2001, 01:25 PM	#10 (permalink)
BadAZYj Registered User Join Date: Aug 2001 Member # 6815 Location: Flagstaff, AZ Posts: 1,992	What is Phil's email address? __________________ Well this sucks...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode