Pirate 4x4 banner

Reaction score
13

Marketplace Rating
(0.0 - 0 reviews)

Profile posts Latest activity Discussions Buy & Sell Reviews About

  • · Registered
    Joined
    ·
    28 Posts
    How do I order slugs for 05 up super 60? Are these hardened? If so, is it possible to purchase prior to hardening? I'm looking to have these cut to 47 spline for ouverson axles

    · Premium Member
    Joined
    ·
    2,040 Posts
    Checking to see if you know the castor to pinion angle spread on a SD 2008 D60.

    Thanks

    · Registered
    Joined
    ·
    51 Posts
    Hello,

    I have been following the super duty d60 thread with much interest. Would you mind confirming if I should jump on these diffs.
    I have the opportunity to purchase the front and rear diffs from a 2012 F350 6.2 gas with 3.73 gearing.
    Can I assume it a D60 front and a Sterling rear?
    Can I get lockers and 5.38 gearing for these?
    Anything to look for while viewing these?
    Should I stay away from them?
    Truck has under 100,000 kms.

    Thanks for your time.

    Don

    · hi-steer ninja
    Joined
    ·
    3,040 Posts
    they were designed for full hydro, no worries. they can be connected if desired also. easier to fit a ram on top of the arms..

    · Registered
    Joined
    ·
    89 Posts
    hey im going to be running full hydro on my front 60. just wondering if these arms can take that pressure ? or can they be drilled to do a double sheer? just trying to see what i need to purchase! thanks

    · Registered
    Joined
    ·
    98 Posts
    Hey, I'm interested in getting my '04 d60 knuckles fitted for hi-steer, only problem I live in Canada. Is this possible for you to do or should I try and source some one local to machine? Thanks

    · Registered
    Joined
    ·
    273 Posts
    C.J. Hey I have one of your knuckles on my Dana 60. Question on wheel clearance, I just ordered the procomp series 5 I believe 16.5x9.75 with 4.5 inch backspacing, I am gonna run good year M/T 37 12.50 r16.5's H1 takeoffs am I gonna clear the knuckle and raised arm with the 4.5 inch backspacing? Thought you might know?! Thanks man Kip

    · hi-steer ninja
    Joined
    ·
    3,040 Posts
    coil spring is 2005-up, it has larger unit bearings. that will be the next kit developed, however i have no time frame i can give currently.

    · Registered
    Joined
    ·
    512 Posts
    I just read some of the thread in axles section. The front end had coil spring mounts so I guess it's a 95 or newer.

    Are you planning on developing anything for 95 and up? What's the difference in the knuckles? Could I run 99-04 knuckles?

    · hi-steer ninja
    Joined
    ·
    3,040 Posts
    jeff, i do the ford unit bearing 99-04 knuckles, a kit runs $450 exchange, i have an ad in the axle vendor section with pics of the knucks and arms, thanx cj

    · Registered
    Joined
    ·
    512 Posts
    I have a set of knuckles i need machined for high steer. Ill be using a double ended ram. Knuckles are off a late model balljoint superduty ford. Not sure of exact year model though. Whats the cost to machine the knucles and attach high steer arms?

    thanks,
    jeff

    · Registered
    Joined
    ·
    57 Posts
    Hey awesome ranger build! Im doing a bronco II 4x4 , i did a axle swap to the 8.8 and also the 94 explorer front end, along with the 4.0 :) Id be done with my rear axle swap if i wasnt working on that 6.0 right now lol
    Thanks for all the info i forgot to mention it does have a new fuel pump and idm replaced by ford 3 months ago.
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Top