Lot of jeep parts - Pirate4x4.Com : 4x4 and Off-Road Forum

Bigcountry · 09-03-2002, 08:42 PM

All of this is about 1 year old and has maybe 2000miles some has less than that. about 100 off road miles
1- Borla S/S header for a 258. $250 new $375
1- Offenhauser manifold for a holley 4 barrel on a 258 $250
1- holley 390 cfm 4bbl carb. $250
1- aluminum valve cover bolt on kind $50
t-18 with low granny and dana 20 case. tranny went through 1 year ago $600
Center force 2 dual clutch with pressure plate and throughout bearing $225
amc 20 with detroit locker and 4.56 gears all new timken bearings and seals drum brakes ok 1 piece superior shafts narrow track $650 professionally built with spring over or under perches on it. nice rubicon express anti wrap perches on top.
dana 30 front with detroit locker 4.56 gears all new bearings and seals new ujoints in shafts with new warn premium hubs drum brakes with all new drum parts and drums and shoes. $650obo professionally built
2-258 motors both run one better than other 1 complete other for parts $400.
Jacobs electronic ignition works really good could tell the differance offroad with it $300 new will take $200. it really made a huge differance in crawling and hp.
3-99 f 250 superduty aluminum wheels and 1 stock steel wheel 8 lug $150
14bolt 3.73 gears i think and open carrier $75
email me at cecinc1@hotmail.com i can ship anything but it will prob. be exspensive for whole axles. thanks

snoop dogg · 09-04-2002, 10:00 AM

you wouldn't happen to have a GOOD 2 barrel carb for a 258..would you consider a trade?? we have a 4 barrel edelbrock carb and performer manifold for a amc 304...what we need is a very good running carb for a 258...also you wouldn't happen to have a 14 bolt 10.5 ring FF 4.10 gears??

EDIT: saw that you have a 4 barrel carb and manifold for the 258...you want to trade??

bluesman2a · 09-06-2002, 09:43 AM

Hey BigCountry, would you consider $200 for the header? I'll come get it, so no shipping hassle...

Bigcountry · 09-06-2002, 10:41 AM

i'm sorry the header was $379.99 plus shipping i really need to get $250 out of it that is as low as i can go it is a really good header i could tell the diff. in the horsepower. it is a little discolored but all of them will turn a little from the heat. you can come and get it for $250 if you want depending on where you i will meet you in gainesville for no charge or in gwinnett for $25 more. thanks let me know. email me cecinc1@hotmail.com or back here if you have any more ?'s.

jeeper17 · 02-04-2003, 12:52 PM

would you be willing to let the valve cover go for 30 bucks?

PGREEN199 · 02-04-2003, 03:49 PM

I take then the t-18 was bolted up behind the 258

Bigcountry · 02-04-2003, 04:20 PM

ttt

nuthugger · 02-05-2003, 01:19 AM

looking for a set of stock yj springs

GRAY TISDALE · 02-06-2003, 08:22 PM

WOULD YOU SALE GEARS AND LOCKER OUT OF M20 BY ITS SELF

Bigcountry · 02-09-2003, 05:50 AM

yes i will sell the gears and lockers out of the m20 do you want the 1 piece shafts too. makes a great combonation. also do you want this stuff shipped or will you come and pick it up. i am in gainesville, ga 30501 if you wanna get shipping costs. prob weigh 20 for the locker and 10 for the gears so around 30-35 pounds i am guessing.

jeeper17 · 02-10-2003, 10:09 AM

I have been trying to contact you. Is the valve cover still for sale?

Will you take $30 for it?

Bigcountry · 02-10-2003, 06:58 PM

no i am sorry i will take $50 plus shipping. i wish i could but this stuff isnt mine it is my dads and he said that is what he wants for it. it is really worth it paid almost $100 for it and has only been used for a couple months and that means like 100 miles if that.

GRAY TISDALE · 02-10-2003, 08:16 PM

How much for the locker and gears I live in Bakersfield Ca 93311 please find out how much shipping cost ?

jeeper17 · 02-11-2003, 08:36 PM

YOU HAVE MAIL

Bigcountry · 04-09-2003, 06:20 PM

hey sorry about the valve cover it is sold and my email was down so i never returned your email after i sold it then a few days later i got my email working again and saw yours.

ttt

GRAY TISDALE · 04-09-2003, 09:22 PM

I'm still interrested in the m20 4:56 geras and locker. Please let me know

Bigcountry · 04-10-2003, 03:23 PM

i will take $700 shipped. you are getting a great on this stuff i have about 950 in just parts. let me know i have to take it out of the jeep so it will take a day or two to pull it. thanks

09-03-2002, 08:42 PM	#1 (permalink)
Bigcountry Wheeler Join Date: Feb 2002 Member # 10184 Location: Gainesville, GA Posts: 272	Lot of jeep parts All of this is about 1 year old and has maybe 2000miles some has less than that. about 100 off road miles 1- Borla S/S header for a 258. $250 new $375 1- Offenhauser manifold for a holley 4 barrel on a 258 $250 1- holley 390 cfm 4bbl carb. $250 1- aluminum valve cover bolt on kind $50 t-18 with low granny and dana 20 case. tranny went through 1 year ago $600 Center force 2 dual clutch with pressure plate and throughout bearing $225 amc 20 with detroit locker and 4.56 gears all new timken bearings and seals drum brakes ok 1 piece superior shafts narrow track $650 professionally built with spring over or under perches on it. nice rubicon express anti wrap perches on top. dana 30 front with detroit locker 4.56 gears all new bearings and seals new ujoints in shafts with new warn premium hubs drum brakes with all new drum parts and drums and shoes. $650obo professionally built 2-258 motors both run one better than other 1 complete other for parts $400. Jacobs electronic ignition works really good could tell the differance offroad with it $300 new will take $200. it really made a huge differance in crawling and hp. 3-99 f 250 superduty aluminum wheels and 1 stock steel wheel 8 lug $150 14bolt 3.73 gears i think and open carrier $75 email me at cecinc1@hotmail.com i can ship anything but it will prob. be exspensive for whole axles. thanks

09-04-2002, 10:00 AM	#2 (permalink)
snoop dogg Registered User Join Date: Mar 2002 Member # 10807 Location: Or Posts: 1,659	you wouldn't happen to have a GOOD 2 barrel carb for a 258..would you consider a trade?? we have a 4 barrel edelbrock carb and performer manifold for a amc 304...what we need is a very good running carb for a 258...also you wouldn't happen to have a 14 bolt 10.5 ring FF 4.10 gears?? EDIT: saw that you have a 4 barrel carb and manifold for the 258...you want to trade?? Last edited by snoop dogg; 09-04-2002 at 10:01 AM.

09-06-2002, 09:43 AM	#3 (permalink)
bluesman2a Registered User Join Date: May 2001 Member # 4554 Location: Atlanta, Ga. USA Earth Sol etc. Posts: 1,261	Hey BigCountry, would you consider $200 for the header? I'll come get it, so no shipping hassle... __________________ M-715 Zombie Control Edition "If your junk didn't come standard with 38's and gun mounts in the cab/bed STFU." -- me

02-04-2003, 12:52 PM	#5 (permalink)
jeeper17 Registered User Join Date: Feb 2003 Member # 16823 Location: Merced, California Posts: 7	aluminum valve cover would you be willing to let the valve cover go for 30 bucks?

02-04-2003, 03:49 PM	#6 (permalink)
PGREEN199 Registered User Join Date: Jan 2001 Member # 2832 Location: USA Posts: 120	I take then the t-18 was bolted up behind the 258 __________________ 1952 CJ3A

09-06-2002, 10:41 AM	#4 (permalink)
Bigcountry Wheeler Join Date: Feb 2002 Member # 10184 Location: Gainesville, GA Posts: 272	i'm sorry the header was $379.99 plus shipping i really need to get $250 out of it that is as low as i can go it is a really good header i could tell the diff. in the horsepower. it is a little discolored but all of them will turn a little from the heat. you can come and get it for $250 if you want depending on where you i will meet you in gainesville for no charge or in gwinnett for $25 more. thanks let me know. email me cecinc1@hotmail.com or back here if you have any more ?'s.

02-04-2003, 04:20 PM	#7 (permalink)
Bigcountry Wheeler Join Date: Feb 2002 Member # 10184 Location: Gainesville, GA Posts: 272	ttt

02-05-2003, 01:19 AM	#8 (permalink)
nuthugger Registered User Join Date: Feb 2003 Member # 16846 Location: Hazel Crest, Il Posts: 40	yj springs looking for a set of stock yj springs

02-06-2003, 08:22 PM	#9 (permalink)
GRAY TISDALE Granite Guru Join Date: Mar 2001 Member # 3605 Location: SUSANVILLE,CA USA Posts: 814	LOCKER AND 4:56 GEARS WOULD YOU SALE GEARS AND LOCKER OUT OF M20 BY ITS SELF

02-09-2003, 05:50 AM	#10 (permalink)
Bigcountry Wheeler Join Date: Feb 2002 Member # 10184 Location: Gainesville, GA Posts: 272	yes i will sell the gears and lockers out of the m20 do you want the 1 piece shafts too. makes a great combonation. also do you want this stuff shipped or will you come and pick it up. i am in gainesville, ga 30501 if you wanna get shipping costs. prob weigh 20 for the locker and 10 for the gears so around 30-35 pounds i am guessing.

02-10-2003, 10:09 AM	#11 (permalink)
jeeper17 Registered User Join Date: Feb 2003 Member # 16823 Location: Merced, California Posts: 7	valve cover I have been trying to contact you. Is the valve cover still for sale? Will you take $30 for it?

02-10-2003, 06:58 PM	#12 (permalink)
Bigcountry Wheeler Join Date: Feb 2002 Member # 10184 Location: Gainesville, GA Posts: 272	no i am sorry i will take $50 plus shipping. i wish i could but this stuff isnt mine it is my dads and he said that is what he wants for it. it is really worth it paid almost $100 for it and has only been used for a couple months and that means like 100 miles if that.

02-10-2003, 08:16 PM	#13 (permalink)
GRAY TISDALE Granite Guru Join Date: Mar 2001 Member # 3605 Location: SUSANVILLE,CA USA Posts: 814	How much for the locker and gears I live in Bakersfield Ca 93311 please find out how much shipping cost ?

02-11-2003, 08:36 PM	#14 (permalink)
jeeper17 Registered User Join Date: Feb 2003 Member # 16823 Location: Merced, California Posts: 7	valve cover YOU HAVE MAIL

04-09-2003, 06:20 PM	#15 (permalink)
Bigcountry Wheeler Join Date: Feb 2002 Member # 10184 Location: Gainesville, GA Posts: 272	hey sorry about the valve cover it is sold and my email was down so i never returned your email after i sold it then a few days later i got my email working again and saw yours. ttt

04-09-2003, 09:22 PM	#16 (permalink)
GRAY TISDALE Granite Guru Join Date: Mar 2001 Member # 3605 Location: SUSANVILLE,CA USA Posts: 814	I'm still interrested in the m20 4:56 geras and locker. Please let me know

04-10-2003, 03:23 PM	#17 (permalink)
Bigcountry Wheeler Join Date: Feb 2002 Member # 10184 Location: Gainesville, GA Posts: 272	i will take $700 shipped. you are getting a great on this stuff i have about 950 in just parts. let me know i have to take it out of the jeep so it will take a day or two to pull it. thanks

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode