Dana 60 Kingpin High Steer Stud Kits Now Available! - Pirate4x4.Com : 4x4 and Off-Road Forum

Reid Racing · 07-08-2003, 04:36 PM

We are now stocking ARP studs, nuts, and washers to fit your Kingpin high steer arms.

* 220,000 psi tensile strength
* .930 shank to fit 1"-1.5" thick arms
* ARP high strength nuts and washers included

D60115K- 5 stud high steer kit $35.00 (5th stud is for the Dedenbear Knuckle)
D60114K- 4 stud high steer kit $29.00

Available Now!

TPIJeep · 07-08-2003, 05:26 PM

I need a 4 stud kit, can this be done online with paypal?

RealJeepMan · 07-08-2003, 08:23 PM

We are not set up for online orders, you can give me a call tomorrow or give me your number and I can call you. We can ship them C.O.D. or Credit Card.

Ryan

BustedRig · 07-08-2003, 09:40 PM

Uh, I hate to beg.......I mean ask, but want about an 8 stud kit? anyway can you give a good deal on those? I mean, why not do both sides at once.

RealJeepMan · 07-08-2003, 10:48 PM

Quote:

Originally posted by BustedRig
Uh, I hate to beg.......I mean ask, but want about an 8 stud kit? anyway can you give a good deal on those? I mean, why not do both sides at once.

We have already priced them as low as we can go, but it never hurts to ask.

Ryan

Reid Racing · 07-10-2003, 08:23 AM

pic of studs installled

SittonHigh · 07-10-2003, 08:43 AM

Can you get them with tapered washers?

Reid Racing · 07-10-2003, 11:01 AM

Quote:

Originally posted by SittonHigh
Can you get them with tapered washers?

No tapered washers. Most people use the stamped steel kingpin cap in conjunction with high steer arms. The steel cap has no provisions for a tapered seat allowing the use of tapered washers or nuts. If you were to taper the holes in the high steer arm, you could no longer run a kingpin cap. I suppose if you wanted to run a factory cast kingpin cap that has the tapers in it on top of the high steer arm, you could run tapered washers. The studs however would need to be longer than what we are offering.
With a properly made high steer arm (holes in the correct locations and correct diameter) the studs fit great and the steering arms do not move at all.

Doug

Eric · 07-14-2003, 09:58 AM

Do you sell the studs without the bolts and washers?

Reid Racing · 07-14-2003, 02:45 PM

Quote:

Originally posted by Eric
Do you sell the studs without the bolts and washers?

No, but I can sell you a single stud, nut, and washer for $9

Ryan

Stephen · 07-22-2003, 11:26 AM

How about a tapered nut or a tapered washer?
Fine thread on both ends? maybe? Then you could use a wide selection of nuts.

Reid Racing · 07-22-2003, 02:25 PM

Tapered nuts would work great with your arms but I do not carry them or have a source for them

Ryan

TONY K · 07-24-2003, 08:34 PM

D60003K- 5 stud high steer kit $35.00 (5th stud is for the Dedenbear Super Knuckle)

Super Knuckle - that's an original name.

RealJeepMan · 07-24-2003, 08:52 PM

Sorry Tony, after I posted it I saw that you offer a super knuckle. I threw that in there because we use it with some of our other products like our Superglide and our Delay Boxes It looks like we have already droped it as a knuckle description.

Ryan

TONY K · 07-25-2003, 07:48 AM

Call them what ever you want. I was just being funny.......

RedBullJeep · 08-10-2003, 01:26 PM

Ryan and Tony...I guess this means that you guys are both SUPER...

TONY K · 08-10-2003, 08:48 PM

I knew you'd be along soon enough, Dustin.

I don't think anyone ever trade marked the word " super " but it was fun to tease Ryan.

tony k

Reid Racing · 12-24-2003, 08:22 AM

Its been a while, but back to the top. Keep the orders comming on these, the demand has been great.

Ryan

Reid Racing · 02-06-2004, 08:10 AM

Bump

Reid Racing · 02-17-2004, 02:59 PM

TTT

Reid Racing · 02-23-2004, 08:47 AM

Keep the orders comming!

Reid Racing · 02-25-2004, 08:05 AM

TOP

Reid Racing · 03-09-2004, 08:30 AM

TOP

Reid Racing · 03-30-2004, 08:28 AM

Bump

Reid Racing · 04-12-2004, 08:23 AM

Top

07-08-2003, 04:36 PM	#1 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Dana 60 Kingpin High Steer Stud Kits Now Available! We are now stocking ARP studs, nuts, and washers to fit your Kingpin high steer arms. * 220,000 psi tensile strength * .930 shank to fit 1"-1.5" thick arms * ARP high strength nuts and washers included D60115K- 5 stud high steer kit $35.00 (5th stud is for the Dedenbear Knuckle) D60114K- 4 stud high steer kit $29.00 Available Now! Attached Images __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA! Last edited by Dedenbear; 02-09-2004 at 09:43 AM.

07-08-2003, 05:26 PM	#2 (permalink)
TPIJeep Zeus of the Sluice Join Date: Oct 2000 Member # 2082 Location: Ruston, Louisiana Posts: 3,043	I need a 4 stud kit, can this be done online with paypal? __________________ I am normally only a danger to myself don't make me include you!! BioHazard Buggy Build Thread Southern Motor Sports Ruston, Louisiana

07-08-2003, 08:23 PM	#3 (permalink)
RealJeepMan Registered User Join Date: Jun 2000 Member # 1170 Location: Concord Ca Posts: 1,525	We are not set up for online orders, you can give me a call tomorrow or give me your number and I can call you. We can ship them C.O.D. or Credit Card. Ryan __________________ 77 CJ7 "One Week Jeep"

07-08-2003, 09:40 PM	#4 (permalink)
BustedRig Registered User Join Date: Mar 2003 Member # 17844 Location: KNOX, TN Posts: 97	Uh, I hate to beg.......I mean ask, but want about an 8 stud kit? anyway can you give a good deal on those? I mean, why not do both sides at once. __________________ Yeah, Yeah Newbie BS title, this is my work listing guys forgot my P-word so FAWK OFF!

07-10-2003, 08:23 AM	#6 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	pic of studs installled Attached Images __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

07-10-2003, 08:43 AM	#7 (permalink)
SittonHigh Registered User Join Date: Apr 2002 Member # 11497 Location: Auburn, Al Posts: 480	Can you get them with tapered washers? __________________ [URL]http://aucrawlers.suddenlaunch.com[/URL] [URL=www.4x4support.com]4X4Support[/URL]

07-14-2003, 09:58 AM	#9 (permalink)
Eric Registered User Join Date: Feb 2000 Member # 39 Location: San Martin, CA Posts: 3,266	Do you sell the studs without the bolts and washers? __________________ Eric Parts for Sale --> D44 shafts, 6 lug rims, air tank

07-22-2003, 11:26 AM	#11 (permalink)
Stephen Granite Guru Join Date: Oct 2000 Member # 2092 Location: Carbondale, CO Posts: 858	How about a tapered nut or a tapered washer? Fine thread on both ends? maybe? Then you could use a wide selection of nuts. __________________ Stephen Watson www.offroaddesign.com #4488 KOH '12 12th overall KOH11 28th. It's a finish! KOH11 Sportsmanship Award. Friends & partners who helped: Offroad Design, Pacific Fab, King, Baja Designs, TrailReady, Amsoil, PSC, Tom Woods, Bighorn Graphics, Superior, Optima

07-22-2003, 02:25 PM	#12 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Tapered nuts would work great with your arms but I do not carry them or have a source for them Ryan __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

07-24-2003, 08:34 PM	#13 (permalink)
TONY K Registered User Join Date: May 2002 Member # 12008 Location: Lincoln Ca. Posts: 1,814	D60003K- 5 stud high steer kit $35.00 (5th stud is for the Dedenbear Super Knuckle) Super Knuckle - that's an original name. __________________ Tony K - Shocks - Sway Bars - Steering tk1racing.com or Facebook.com/tk1racing

07-24-2003, 08:52 PM	#14 (permalink)
RealJeepMan Registered User Join Date: Jun 2000 Member # 1170 Location: Concord Ca Posts: 1,525	Sorry Tony, after I posted it I saw that you offer a super knuckle. I threw that in there because we use it with some of our other products like our Superglide and our Delay Boxes It looks like we have already droped it as a knuckle description. Ryan __________________ 77 CJ7 "One Week Jeep"

07-25-2003, 07:48 AM	#15 (permalink)
TONY K Registered User Join Date: May 2002 Member # 12008 Location: Lincoln Ca. Posts: 1,814	Call them what ever you want. I was just being funny....... __________________ Tony K - Shocks - Sway Bars - Steering tk1racing.com or Facebook.com/tk1racing

08-10-2003, 01:26 PM	#16 (permalink)
RedBullJeep Pirate is KING! Join Date: Jun 2002 Member # 12217 Location: San Diego Area Posts: 13,503	Ryan and Tony...I guess this means that you guys are both SUPER... __________________ . Dustin Webster Red Bull RockCrawling Team RockHer 1 - SOLD STILL FOR SALE - Toter and trailer, RockHer 2, and KOH TJ. Click for details

08-10-2003, 08:48 PM	#17 (permalink)
TONY K Registered User Join Date: May 2002 Member # 12008 Location: Lincoln Ca. Posts: 1,814	I knew you'd be along soon enough, Dustin. I don't think anyone ever trade marked the word " super " but it was fun to tease Ryan. tony k __________________ Tony K - Shocks - Sway Bars - Steering tk1racing.com or Facebook.com/tk1racing

12-24-2003, 08:22 AM	#18 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Its been a while, but back to the top. Keep the orders comming on these, the demand has been great. Ryan __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

02-06-2004, 08:10 AM	#19 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Bump __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

02-17-2004, 02:59 PM	#20 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	TTT __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

02-23-2004, 08:47 AM	#21 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Keep the orders comming! __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

02-25-2004, 08:05 AM	#22 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	TOP __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

03-09-2004, 08:30 AM	#23 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	TOP __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

03-30-2004, 08:28 AM	#24 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Bump __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

04-12-2004, 08:23 AM	#25 (permalink)
Reid Racing Wheeler Join Date: Jun 2003 Member # 20872 Location: Pleasant Hill, CA Posts: 397	Top __________________ Join the fight to keep public lands open to the public! Manufacturers of Dana 60, 44, 30, 10-Bolt & JK knuckles and Turbo400 & Powerglide transmission cases. (925) 935-3025 M-F 8-6pm PST race.mail@reidracing.biz http://www.reidracing.biz Built by racers for racers! Made in the USA!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode