|05-12-2012 08:52 PM|
You still working on this bike, because I would like to see how it comes out?
|03-05-2012 09:42 PM|
Back bone fab
Cafe Racer Episode 8 New Back Bone - YouTube
|11-30-2011 11:12 AM|
Lucky number 7. I really hit an awesome point here getting the rear race bump done and it looks killer.. Also my edits are getting pretty good too.. Music and sound are coming together in this one.
Cafe Racer Build Epidsode 7 Looking Good - YouTube
|11-24-2011 06:28 PM|
Watch me weld up an 18ga. box and gain the confidence to weld up the bodywork on the bike.. This is 8 min of me making a box.. No I will not give you your 8 min back.
Cafe Racer Episode 6. Building a Box - YouTube
|11-22-2011 05:35 PM|
|jeep937||Working on the next video and making some progress with the welder.|
|11-15-2011 11:57 AM|
Cafe Racer Build 4.5 NEW TOOLS! - YouTube
|11-14-2011 09:03 PM|
Honda 360 Cafe Racer Episode 4 - YouTube
|11-08-2011 02:46 PM|
good choice on the kawasaki tank...i may be biased though
|10-06-2011 11:45 AM|
|jeep937||Honda 360 Cafe Racer Episode 3 - YouTube|
|10-04-2011 04:36 PM|
Love the cafe bikes. Here's a couple before and almost done shots of my cb750.
|10-04-2011 03:00 PM|
Honda 360 Cafe Racer Part 2 - YouTube
|09-25-2011 11:47 PM|
Made some progress.. About half done fabbing the seat pan and rear hump section. Also filming for episode 2..
|09-25-2011 07:39 AM|
If you had taken the headlight out you'd find all the wiring from the bars is connected with bullet connectors, easy to disconnect and pull through the bars.
Look around here, it's not specifically a 2 cylinder forum but there are a lot of knowledgeable people there. http://forums.sohc4.net/
|09-24-2011 12:58 PM|
Stupid video I made
Honda 360 Cafe Racer - YouTube
|09-24-2011 12:42 PM|
Final patten for the seat pan and hump
|08-31-2011 01:28 PM|
I have one at home that's bone stock if you need any measurements, pics, whatever.
Some inspiration for you...
|08-31-2011 12:24 PM|
|jeep937||It's a tank from a '76 KE100. I like it cause it's a lot smaller than the 360 tank.|
|08-31-2011 10:49 AM|
|dog walker||Youre Honda looks like a Kawasaki.|
|08-30-2011 11:26 PM|
Stupid fucker took a deep chunk out of my finger so I took the grinder to it..
Here's 6' 220#, at a bad camera angle, with my feet on the passenger pegs. I think I'm gonna move them up about 4 inches and it'll be just right.
Here's 6' 2" 155# with his feet on the front peg area.. Better angle.
And before I went in for the night I had to do a quick little cut and tape mock up.. Gotta get that tank down in the back but I think it's gonna be pretty tits..
|08-30-2011 10:51 PM|
|Ben Segrest||I've been wanting to do a cafe bike for a while now. The wiring should be really simple on that, I say rip it out and start over.|
|08-30-2011 05:09 PM|
Striping it down..
|08-30-2011 01:47 PM|
Honda CB360 Cafe' Racer
So I got this bike for real cheap and want to make it a Cafe Racer.. It ran and everything worked on it. Until... I did this..
Trying to get the hand controls off I had to cut the wires that ran through the bars up to the controls. I cut them so I could technically get it all back together if I needed but they are all beat and broken so I probably won't..
Looking at all the wiring on the bike I'm thinking of just ripping it all out and redoing it. I'm pretty good at wireing I've just never messed with a bike before and am a little gun shy about ripping it all out...
Also the cables going to the levers are a little complicated.. I'm having a hard time getting them all disconnected as well. Any tricks here?
Know of any cheap hand controls with cable brake or should I just use what I got and try to make it all work?