|04-12-2017 12:58 PM|
Putting a 6.0 and 4l65 in the Scout - so selling the IH take out package.
IH 345, TF727, D300
International 345 from a '73 Scout II with the following upgrades:
IH Only aluminum intake manifold
scoutparts 4 to 1 headers -sold
mean green starter
mean green alternator
converted ac compressor to on board air
No smog equipment
Dana 300 with 4:1 gears and twin sticked - sold
I have had the truck about a year. Mileage shows ~530 on the odo -- not sure how many times it has rolled over. motor, torqueflite 727, and dana 300 all in good working condition. It's been up the Rubicon a couple times and driven around the streets. EFI kit was dialed in and made for easy starts.
Looking to sell as a package for $2500. Will start to part out the pieces this weekend. Make an offer or come by and grab what you need and make a deal.
Looking to get $800 for the Howell EFI, $300 for intake manifold. The rest make an offer.
Located in Rancho Cordova, CA
|03-28-2017 08:16 AM|
|smokd||Looking for a 4x4 crossmember for a divorced 205 tcase and shifter assembly|
|03-08-2017 07:42 PM|
I have a pair of Squarebore intakes for $100 ea.
Shipping will probably kill the deal.
|02-11-2017 10:05 AM|
|email@example.com||I need a rear axle shaft for the RA10 in the back of a '56 s120. I'm in Michigan, Kansas, Minnesota, Wisconsin, often.|
|01-25-2017 12:33 PM|
1 Ton Scout Project For Sale
1980 International Scout Project- Planned for rocks, mud, trails, etc. Big items are done. Long term project like most that don't get finished, life gets in the way and priorities change. Get ready, Below is a novel, I'm sure I'll miss something. Don't be afraid to call or text questions. Open to offers and trades. Thanks- Charlie
Front- Chevy (king-pin) Dana 60 4.56 Spring over/reverse shackle. Done right with no fangs hanging down. Front axle pushed forward to stretch the wheel base. Cross-over steering with high steer arms. All completed at 4x4Land in Topeka. Needs calipers.
Rear- 14 Bolt 4.56 with Detroit locker. Spring Over. Needs perches welded. Ruff Stuff disc brake brackets not installed. Needs Drive shafts.
Motor- Chevy 350. Good running motor prior to install. Stock internals. All new accessories. (Intake, Carb, Fuel pump, Headers, Alt, Distributor, Water pump, Starter, March brackets, etc.) Sitting on welded in Advance adapter motor mounts. Still need power steering pump. Haven't ran fuel lines or electrical. haven't fired since swap.
Trans- Turbo 350, K Case. Sitting on custom mount that would allow doubler to be installed in the future.
Transfer Case- NP205, Twin sticked. All tucked up between frame rails for clearance.
Body- 1973 grill. Some typical Scout rust but less than you see in most. Honestly a pretty solid scout. Drivers floor is the worst (95% of floor in above average shape), rockers and some in front of rear wheel wells. I planned to replace rockers with square tube. Most in front of rear wheels would be cut out for tire clearance. Speaking of tire clearance front fenders already cut and rolled. Inner fenders still need work. Top is removable in case you didn't realize. Great shape around hinges. I haven't pulled interior panels to look at rails. Looking at header I'm going to guess its never been removed. I have 3 extra doors, 2 extra fenders, 1 extra tailgate and 1 extra hood.
Interior- Pulled out stock seats, door panels, and carpet. I have a black pair of Corbeau Baja SS seats for the front (great shape- stored in my basement). Scout seat bases are solid. Scout console base is solid, plastic top is cracked. Dash in good shape no cracks. I was going to cut diamond plate aluminum for door panels and spray floor with bedliner.
Tires- Currently on rollers (have never lost air). I have pics with it on 35s and 42's. The plan was 39.5-42's and cutting fenders to make fit. Great stance on 42's looked killer.
I have lots of pics if you want to see before looking in person. If you can't tell, I was really trying to build it right the first time. All the big components are in place. Just need to tie them all together. Lots of parts, you'll get them all. Not hurting for money so no lowball offers but motivated seller willing to hear offers. $3500OBO.
Call or text Seven85.783.Two174
The trade question seems to always come up... Open to ideas but no junk. Cash is King. Possible interests- Utility-type 4 wheeler, side by side, 3-pt tractor tiller or food plot implement, zero turn mower, hunting items. I have lots of interests, worst I can say is no.
|01-21-2017 04:00 PM|
scout II top interior pieces.
Both sides and back strip with done light switch. Used but in good condition. Text for pictures. 661- 9 zero 3- zero zero 95 located in Bakersfield ca.
|01-21-2017 06:19 AM|
Scout II and Other Miscellaneous Parts
Have odds and ends of things. Located in Boston area of Massachusetts. Off of different Scout IIs, IH bus
1- 2brl 345 or 392 intake, good shape. Circa 1982 bus. $20.
1- 2brl Holley off of the above. Circa 1982 IH bus. $20.
1- MSD Blaster 2 coil, used, good shape, works. $10.
2- complete sets of spark plug wires. Moroso Bluemax and house brand. Free.
1- Sanden converted AC air compressor. For on board air.
1- IH Only North (IH Parts America) Sanden compressor bracket $15. Used.
1- 1978 Scout II AC condensor. Tested good. Flushed. $20.
1- Performance Distributors HEI DUI red cap distributor. 2 months old. DOn't need it. Like new, currently installed in Scout II. $300.
3- 345, 392 thermostat waternecks. $10/ EA
1- IH Holley distributor, used. $50.
Bunch of odds and ends of ignition parts, like new or new, but hate to throw away. Ask away. Have a few new radiator hoses.
PM me please. Will post pics when I have time. All items can be shipped on your dime. Ship from 02170.Take it all with a good offer of $425.
|01-19-2017 07:54 PM|
|Giterdunn||Looking for a C series truck heater box|
|12-19-2016 10:12 AM|
Windshield wiper pivot
Looking for a windshield wiper pivot for a Scout 800.
|11-12-2016 07:46 AM|
I have 2 sets of scout II rear 44 shafts in good shape. Free in SoCal.
PM if interested
|10-19-2016 08:32 AM|
76 scout II with the sd33t t19 and Dana 300.
body on the scout is dented but has minimal rust. Axles are dana 44s, front has been cut and turned for castor. The rear has a lockright locker. Have the full top and fiberglass half cab bulkhead. Lifted 4 inches with yj springs in the front. hydro boost brakes. $5500
Have a lot of scout parts, axles, another scout II, fenders, inner fenders.....
located Fayetteville Ohio about an hour east of Cincinnati, I can email pics thanks.
|10-18-2016 07:42 PM|
I've got another one. I need an early style turn signal switch for a Scout 80. It's the all metal one. If someone has pulled a column out that had that switch in it I'll buy the whole column if I have to.
|08-31-2016 04:33 PM|
IH 354/AFI TBI/700R4 Combo for sale
Upgrading the project and selling the current motor/trans combo
Ready to install package consists of:
Rebuilt IH 345 with approximately 35K miles
AFI TBI system on RPT aluminum intake manifold
Stan's Tri-Y headers, Jet-Hot coated
York air compressor
DUI distributor and LiveWires
CPT Transmission adapter GM Auto to IH engine
B&M Racing GM 700R4 with lock-up converter (overdrive)
To see the motor and transmission running. Taken only a couple of days before removal from the Scout:
For pictures of the current project and motor:
Asking $3500 for the whole package, not selling as pieces/parts, and is currently located in Grass Valley, CA. If interested please email Darren at firstname.lastname@example.org
|07-30-2016 11:16 PM|
Just re-geared my Scout II Dana 44's and have some extra parts.
All parts from 1977 Scout II Dana 44 axles. All prices are plus shipping from 39556.
Front Dana 44 carrier and gears, 3.54:1 $50
Front Dana 44 knuckles $50
Scout II stock steering pitman arm $25
Rear Dana 44 carrier and gears, 3.54:1 $50
Make offers this stuff is heavy and will end up in the scrap iron bin soon.
|07-19-2016 09:53 AM|
|07-14-2016 05:14 AM|
|Clegg||WANTED: Manual pedal assembly for scout 2. Shipped to 89506|
|07-13-2016 03:15 PM|
I have some parts that I will be selling from my 1966 travelall.
1.A running 304 engine seems to run really good.
2. All four doors, front doors have good glass, rear doors have no glass,rear drivers door has no latch, they look to be solid.
3. The glass for the back tailgate.
|07-01-2016 06:07 AM|
I've got a '70 Scout 800 I am parting out what I can befor the carcass goes to scrap. I have the axles. The doors are spoken for. All other sheet metal is pretty much shit. Had a decent half cab and bulkhead. 6cyl stick.
Mainly, if you need a hard to find small part I have it.
PM me with needs as I don't frequent the IH section. Not looking to make a profit, just want to see stuff put to use.
|06-12-2016 09:45 PM|
parting out a 72 scout II. Will be parting out what I don't need.
Top with sliding Windows. Rear hatch here but hinges broke.
Doors with glass and wind wings includes door panels
Windshield and frame surface rust but no cancer
Grill off of a 76
Tub but rear floor is rotted thru.
dana 30 front and 44 rear with power lock.
Pm me if interested. call or text for price and pictures 661.903.0095
|06-12-2016 04:40 PM|
Early style (driver fender mount) heater box and the crossover duct that goes on the firewall for an early Scout 80.
|06-08-2016 03:19 AM|
IH Garage Sale
Few Scout parts for sale in south MS, 39556
'68 Scout 800, 266ci 4.3L V8, Complete and running engine. Currently on a test stand in the shop. No smoke and runs great. -$1200
'68 scout 800, T-18 transmission and Dana 20 transfer case- $200
'67 Scout 800,Stock Scout Axles Dana 27 front and Dana 44 Rear. -$100
'67 Scout 800, Heater assembly: box, core, blower and motor. -$50
|05-31-2016 02:48 PM|
Rear Dana 44 3.55 and Bestop top
I'm selling the rear Dana 44 out of my traveler. I swapped in an axles with 3.73 gears. It's is open I have drum brakes i will send with it.
Willing to ship on buyers dime.
300obo + shipping.
I also have a scout II soft top. The Canvas is in pretty good shape has one small Tear (see picture) should be repairable.
I've never use this top so it may be missing hardwear. See pictures for what I have.
Let me know if you have questions.
Asking $250 plus shipping.
|05-18-2016 10:01 AM|
Anyone want a 66 IH scout 800? No title, fenders, hood or grill, but the 1/2 cab top is awesome and the doors are reasonable (missing the roll up mechanism tho). Motor won't turn over, but tranny goes in and out of gear and the brakes work.
Looks to be pretty much 100% stock.
Good for parts or the beginnings to a crawler.
Located in Las Vegas, NV
Some bad pics.
|05-18-2016 09:30 AM|
1976 scout ll radiator
No leaks , no rust
$100 plus shipping
|05-16-2016 02:30 PM|
good distributor for 304 with 2 barrel carb
had holley aluminum body straight points with vacum advance
want to go to electric
think thats curved points version
|This thread has more than 25 replies. Click here to review the whole thread.|