Full Floater Axle housing Jig - Pirate4x4.Com : 4x4 and Off-Road Forum

66CJdean · 10-31-2008, 03:00 PM

These are made to support the spindle for axle housing narrowing of Dana 60's, 70's or GM 14 Bolt housings. They also fit the Dana 60 front spindles too. They are turned from solid 7075 so the threads are true to the bore so your alignment is right-on. After one housing you have them paid for. The photo shows the FF jigs on top of the carrier cap jigs.
$250 for the pr
Add $85 for a pr of carrier pucks
Add $200 for an 84" heat treated, hard chrome plated, jig bar.
Or $425 for the whole kit.
Semifloat kit goes for $325

kpj · 10-31-2008, 04:10 PM

These work great!!! I have a set from him that I bought probably 7 years ago and still use them to this day. Great, easy to use product, that makes building custom width rear ends pretty much fool proof.

66CJdean · 10-31-2008, 04:42 PM

Quote:

Originally Posted by kpj

These work great!!! I have a set from him that I bought probably 7 years ago and still use them to this day. Great, easy to use product, that makes building custom width rear ends pretty much fool proof.

Glad you like them. These are now 7075 rather than 6061 so I expect the life span to be even greater than ever. I built my first set of these about 10 years ago and still use them today.

C/K3500 · 11-03-2008, 09:00 AM

Quote:

Originally Posted by 66CJdean

These are made to support the spindle for axle housing narrowing of Dana 60's, 70's or GM 14 Bolt housings. They also fit the Dana 60 front spindles too. They are turned from solid 7075 so the threads are true to the bore so your alignment is right-on. After one housing you have them paid for. The photo shows the FF jigs on top of the carrier cap jigs.
$250 for the pr
Add $75 for a pr of carrier pucks
Add $150 for a jig bar.
Or $400 for the whole kit.

Do you have anything for Sterling 10.25?

66CJdean · 11-03-2008, 11:20 AM

Not sure if they fit or not. I wouldn't doubet it but you would have to do some measuring for me find out spindle OD and carrier cap OD.

PAToyota · 11-04-2008, 02:23 PM

How about for a Ford 9"?

AggieTJ2007 · 11-04-2008, 06:31 PM

I could use a set for ford nine large bearing carrier to use with 1.500 shaft

66CJdean · 11-05-2008, 01:06 PM

Quote:

Originally Posted by AggieTJ2007

I could use a set for ford nine large bearing carrier to use with 1.500 shaft

$325 for the semifloat jig set. The ones for the housing ends fit both set 10 and set 20 bearings.

Appalachian Offroad · 11-05-2008, 03:05 PM

already have a bar... what size bar hole do you machine in these? would you sell just 1?

66CJdean · 11-06-2008, 09:52 AM

Quote:

Originally Posted by Appalachian Offroad

already have a bar... what size bar hole do you machine in these? would you sell just 1?

Just mic your bar and let me know what it is so I can send you the right one. I have a few different sizes but all 1.500 to 1.509 is the span. I am willing to sell just one and that is $150

Azzy2000 · 11-07-2008, 09:26 AM

Very nice. Exactly what I've been looking for. I will be ordering soon.

AKBroncoII · 11-28-2008, 10:05 PM

Great quality, I appreciate the quick turn around with the special order. He machined out a bushing or me down to 1.25"s for the bar I already had Very good to work with, quick communication. Very happy with the way it turned out. Can't wait to use it.

Arya Ebrahimi · 12-08-2008, 09:57 AM

You offer anything for doing 'yota housings?

Twisted Minis · 12-21-2008, 06:37 PM

Would you make ends to do a Ford small bearing? I usually do big, but have been doing some small bearing axles for Mustangs running Versailles brakes lately.

66CJdean · 12-22-2008, 08:29 AM

Sure. I might even have some here already done. They are $65pr

Quote:

Originally Posted by Twisted Minis

Would you make ends to do a Ford small bearing? I usually do big, but have been doing some small bearing axles for Mustangs running Versailles brakes lately.

daniel04 · 01-10-2009, 07:48 PM

need a kit for a d60FF sent to 80260

thanks, Dan

Magnum_Willys · 01-11-2009, 03:59 PM

How about a paragraph on how you or others use these ? Does your bar go all the way across ?

Booger Weldz · 01-11-2009, 09:37 PM

dean, what do you charge to narrow a rear end? i could probably get away with lopping one side off/ weld new spindle and resplining the existing shaft(dana70)... thanks

66CJdean · 01-14-2009, 07:49 AM

Quote:

Originally Posted by Booger Weldz

dean, what do you charge to narrow a rear end? i could probably get away with lopping one side off/ weld new spindle and resplining the existing shaft(dana70)... thanks

You will need a replacement shaft or find one from the junkyard that is the width you want that we can cut to. stock full float shafts are not resplineable due to the kneck down. One side is $150.

I'll send a quote with shipping on that jig bar set up.

66CJdean · 01-14-2009, 08:00 AM

Quote:

Originally Posted by Magnum_Willys

How about a paragraph on how you or others use these ? Does your bar go all the way across ?

Yes the jig bar goes all the way through the housing. You have to pucks that go in the carrier caps and then two for the outers. The full floater jigs thread onto the spindles and then you slip them on the bar or if you have a semifloat there are two other pucks that slip into the housing ends and then slide them onto the bar.

SPEEDCRAVIN · 02-06-2009, 07:25 PM

I need a set of your Jigs,,, I sent you a PM

Thanks, JOSH

Freshman · 02-08-2009, 08:03 AM

can I get a price shipped to 95401 for the hole kit.

Thanks Eric

66CJdean · 02-08-2009, 01:21 PM

I assume you are talking about the FF kit. Since you are close shipping is only $21 so $446 total. The FF jigs I have right now are steel not aluminum if that matters to you. I started making some steel one since that is what some people had asked me to do.

Quote:

Originally Posted by Freshman

can I get a price shipped to 95401 for the hole kit.

Thanks Eric

PAToyota · 02-09-2009, 06:42 AM

Got a FF set from Dean the other week. Very nice! Have to get some pics up of it, but have been working overtime and no time to get out to the shop.

SPEEDCRAVIN · 02-10-2009, 04:42 AM

Quote:

Originally Posted by SPEEDCRAVIN

I need a set of your Jigs,,, I sent you a PM

Thanks, JOSH

Thanks for calling me on a Sunday Dean... I enjoyed BSin with you and I am looking forward the the browntruck showing up. I have some work to do

JOSH

10-31-2008, 03:00 PM	#1 (permalink)
66CJdean Pirate4x4 Addict! Join Date: May 2000 Member # 940 Location: Lincoln, Ca Posts: 6,397	Full Floater Axle housing Jig These are made to support the spindle for axle housing narrowing of Dana 60's, 70's or GM 14 Bolt housings. They also fit the Dana 60 front spindles too. They are turned from solid 7075 so the threads are true to the bore so your alignment is right-on. After one housing you have them paid for. The photo shows the FF jigs on top of the carrier cap jigs. $250 for the pr Add $85 for a pr of carrier pucks Add $200 for an 84" heat treated, hard chrome plated, jig bar. Or $425 for the whole kit. Semifloat kit goes for $325 __________________ WWW.PCRYO.COM Deep Cryogenic Tempering Service Find all my products at www.KICKASSOFFROAD.COM 916-434-6978 Custom Axles built to order. Got 40 spline? I have the hubs, spindles, and axles you need to kickass! Custom Hummer wheels and centers Axle Resplining

11-03-2008, 11:20 AM	#5 (permalink)
66CJdean Pirate4x4 Addict! Join Date: May 2000 Member # 940 Location: Lincoln, Ca Posts: 6,397	Not sure if they fit or not. I wouldn't doubet it but you would have to do some measuring for me find out spindle OD and carrier cap OD. __________________ WWW.PCRYO.COM Deep Cryogenic Tempering Service Find all my products at www.KICKASSOFFROAD.COM 916-434-6978 Custom Axles built to order. Got 40 spline? I have the hubs, spindles, and axles you need to kickass! Custom Hummer wheels and centers Axle Resplining

11-04-2008, 02:23 PM	#6 (permalink)
PAToyota Pirate4x4 Addict! Join Date: Oct 2004 Member # 37600 Location: South Central Pennsylvania Posts: 6,385	How about for a Ford 9"? __________________ GET INVOLVED - Join the Blue Ribbon Coalition SIGN THE PETITION - SAVETHEHAMMERS - #85 '93 Chevrolet 6.5TD K2500 NV4500 Std. Cab Longbed 170K '85 Toyota 22R RN60 4x4 Std. Cab Shortbed 178K (Currently retired for rebuild)

11-05-2008, 03:05 PM	#9 (permalink)
Appalachian Offroad Wheeler Join Date: Sep 2007 Member # 99787 Location: Maryland Posts: 190	already have a bar... what size bar hole do you machine in these? would you sell just 1? __________________ Appalachian Offroad Inc 410-848-2942 Westminster, Maryland Tube bending/notching, Rollcages, Differential Repair and Modification, Suspension, Chassis--> Turnkey, Custom Axles, Alignments Need pricing on any of the following product lines? Yukon, Rubicon Express, PRP Suspension Seats, Dana Spicer, Eaton, or Advanced Adapters..... Give us a call, pm us or stop by the shop for pricing or estimates.

12-08-2008, 09:57 AM	#13 (permalink)
Arya Ebrahimi Zeus of the Sluice Join Date: Oct 2001 Member # 7876 Location: Rockville, MD Posts: 4,214	You offer anything for doing 'yota housings? __________________ DD/Tow-rig: '06 GMC Sierra 2500HD Duramax Classic Rig: '88 FJ62, 100% stock In the weeds waiting for resurrection: '94 FZJ80, 33s, locked

10-31-2008, 04:10 PM	#2 (permalink)
kpj Rock God Join Date: Sep 2001 Member # 6920 Location: Amesbury, MA Posts: 1,815	These work great!!! I have a set from him that I bought probably 7 years ago and still use them to this day. Great, easy to use product, that makes building custom width rear ends pretty much fool proof.

11-04-2008, 06:31 PM	#7 (permalink)
AggieTJ2007 Registered User Join Date: Jan 2005 Member # 41359 Location: Dallas, TX Posts: 211	I could use a set for ford nine large bearing carrier to use with 1.500 shaft

11-07-2008, 09:26 AM	#11 (permalink)
Azzy2000 Mr. Personality Join Date: May 2002 Member # 11869 Location: Yukon, OK Posts: 4,264	Very nice. Exactly what I've been looking for. I will be ordering soon.

11-28-2008, 10:05 PM	#12 (permalink)
AKBroncoII Registered User Join Date: Jan 2003 Member # 16438 Location: Anchorage,AK Posts: 177	Great quality, I appreciate the quick turn around with the special order. He machined out a bushing or me down to 1.25"s for the bar I already had Very good to work with, quick communication. Very happy with the way it turned out. Can't wait to use it.

12-21-2008, 06:37 PM	#14 (permalink)
Twisted Minis Registered User Join Date: Jun 2006 Member # 73728 Location: Santa Rosa, CA Posts: 116	Would you make ends to do a Ford small bearing? I usually do big, but have been doing some small bearing axles for Mustangs running Versailles brakes lately.

01-10-2009, 07:48 PM	#16 (permalink)
daniel04 Wheeler Join Date: Sep 2006 Member # 79753 Location: Denver CO Posts: 144	need a kit for a d60FF sent to 80260 thanks, Dan

01-11-2009, 03:59 PM	#17 (permalink)
Magnum_Willys Registered User Join Date: Dec 2003 Member # 25643 Location: Longview, WA Posts: 797	How about a paragraph on how you or others use these ? Does your bar go all the way across ?

01-11-2009, 09:37 PM	#18 (permalink)
Booger Weldz DuCaTi MoNsTeR Join Date: Jan 2001 Member # 2931 Location: oakdale, ca Posts: 12,424	dean, what do you charge to narrow a rear end? i could probably get away with lopping one side off/ weld new spindle and resplining the existing shaft(dana70)... thanks __________________ Amongst the best of the toyota vendors: *Www.4wheelunderground.com* *Www.addictedoffroad.com* *Www.hellfire-fabworks.com*

02-06-2009, 07:25 PM	#21 (permalink)
SPEEDCRAVIN Registered User Join Date: May 2004 Member # 30432 Location: Dallas Texas Again! Posts: 1,640	I need a set of your Jigs,,, I sent you a PM Thanks, JOSH __________________ SHOP AND APPARTMENT FOR SALE [url]http://pirate4x4.com/forum/showthread.php?t=589523[/url]

02-08-2009, 08:03 AM	#22 (permalink)
Freshman Registered User Join Date: Feb 2002 Member # 9853 Location: Santa Rosa, CA Posts: 510	can I get a price shipped to 95401 for the hole kit. Thanks Eric __________________ 68 Toyota Landcrusier buggy, 42" Irocks, All types of gear setups in the north bay. PM me

02-09-2009, 06:42 AM	#24 (permalink)
PAToyota Pirate4x4 Addict! Join Date: Oct 2004 Member # 37600 Location: South Central Pennsylvania Posts: 6,385	Got a FF set from Dean the other week. Very nice! Have to get some pics up of it, but have been working overtime and no time to get out to the shop. __________________ GET INVOLVED - Join the Blue Ribbon Coalition SIGN THE PETITION - SAVETHEHAMMERS - #85 '93 Chevrolet 6.5TD K2500 NV4500 Std. Cab Longbed 170K '85 Toyota 22R RN60 4x4 Std. Cab Shortbed 178K (Currently retired for rebuild)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode