New Hydraulic Tube Bender from ProBender.com for under $600 (Accepts Pro Tool & JD2) - Page 7 - Pirate4x4.Com : 4x4 and Off-Road Forum

TMI · 03-09-2009, 10:55 AM

I already talked to him this morning. He was just wanting to make sure he was getting the pirate discount

TMI · 03-16-2009, 09:49 AM

New 4,000 PSI Electric/Hydraulic Pump & Ram Package for the ProBender Benders

Now for only $999.95 extra you can order your Pro3 or Pro4 with the 4,000 PSI Electric/Hydraulic Pump & Ram Package. So for the guys that don't want to run the bender with air you can just plug it into the 110v wall socket.

With this addition we know that you cannot find a better bender on the market for the money. Period.

To add the 4,000 PSI Electric/Hydraulic Pump & Ram Package your bender order? Just check it as an option that you want for your new bender.

1982cj7 · 03-16-2009, 09:33 PM

I got the bender put together, i am wondering if the gap next to the die is too much? There is about 3/4" gap between the die and the arm, is this ok or should I cut down the spacers?

99tantj · 03-16-2009, 10:38 PM

Are those the 1/2" or 5/8" arms?

TMI · 03-17-2009, 09:03 AM

Quote:

Originally Posted by 1982cj7

I got the bender put together, i am wondering if the gap next to the die is too much? There is about 3/4" gap between the die and the arm, is this ok or should I cut down the spacers?

You are fine. I built in a extra gap when I started making the 1/2". It makes it easier to get the dies on and off.

On another note: The base is needed before you start bending.

let me know if you have any more questions.

TMI · 03-17-2009, 09:04 AM

Quote:

Originally Posted by 99tantj

are those the 1/2" or 5/8" arms?

1/2"

1982cj7 · 03-17-2009, 07:07 PM

I am building a base for it, I will have it done before I do any bending.

99tantj · 03-18-2009, 05:32 AM

I may be mistaken, but it looks like you might have the ram connected to the wrong bolt. This is how I did mine.
I think this is right, then again I may be the one that has it wrong. I also added a couple sleeves on both sides of the ram
just to keep it centered.

TMI · 03-18-2009, 06:45 AM

Quote:

Originally Posted by 99tantj

I may be mistaken, but it looks like you might have the ram connected to the wrong bolt. This is how I did mine.
I think this is right, then again I may be the one that has it wrong. I also added a couple sleeves on both sides of the ram
just to keep it centered.

The ram is on the right bolt. Looks great

99tantj · 03-18-2009, 12:33 PM

Thanks, it would look a LOT better with some tube sticking out of it.

1982cj7 · 03-18-2009, 05:57 PM

I will have to switch mine, in the directions it looked like it was hooked up the way I have it. I still have to paint it yet anyway.

TMI · 03-18-2009, 08:21 PM

Quote:

Originally Posted by 1982cj7

I will have to switch mine, in the directions it looked like it was hooked up the way I have it. I still have to paint it yet anyway.

????? Please call me if you have any questions?

I am here to make sure that you successed... So if you are unsure please call me and I will walk you threw it.... Rob

72blazer · 03-24-2009, 08:28 PM

PM sent

TMI · 03-25-2009, 07:06 AM

PM sent back

spidr · 04-01-2009, 11:18 AM

Pm sent.

TMI · 04-01-2009, 11:52 AM

Quote:

Originally Posted by spidr

Pm sent.

PM sent back.

TMI · 04-01-2009, 02:50 PM

Spidr-

I got the pipe section fixed on the website. Thanks for bringing it to my attention.

Hardstripe · 04-07-2009, 07:42 AM

got ahold of him, was very helpful and answered all my questions, finished my order a second ago.

SeaBass44 · 04-07-2009, 07:54 AM

Quote:

Originally Posted by Hardstripe

ive been calling for like a week with no response, is this business still open?

last reply 6 days ago above yours...........maybe vacation

TMI · 04-07-2009, 10:39 AM

Quote:

Originally Posted by Hardstripe

ive been calling for like a week with no response, is this business still open?

What???

Yeah I am still open.

I have 2 log calls from your 509#

April, 6 6:12 PM
April, 7 9:39 AM

We are open from 10AM-4:30PM CST

Please call between thows hours if you want someone on the phone.

TMI · 04-07-2009, 10:40 AM

Quote:

Originally Posted by SeaBass44

last reply 6 days ago above yours...........maybe vacation

Vacation??? I wish....

Sundevil · 04-08-2009, 08:37 AM

What is the advantange of switching over to the Hydraulic system over the air/Hydraulic system?

More bending power? faster? more control?

TMI · 04-08-2009, 10:05 AM

Quote:

Originally Posted by Sundevil

What is the advantange of switching over to the Hydraulic system over the air/Hydraulic system?

More bending power? faster? more control?

Just faster but Air/Hydraulic system I think has more control.

TMI · 04-16-2009, 09:23 AM

Free Bend-Tech EZ with purchase of a Pro3 or Pro4 bender is almost over.
Offer End's 05/01/2009.

Hardstripe · 04-18-2009, 01:01 PM

hey I sent you a pm concerning my order

03-09-2009, 10:55 AM	#151 (permalink)
TMI Granite Guru Join Date: Nov 2008 Member # 122938 Location: MN Posts: 637	I already talked to him this morning. He was just wanting to make sure he was getting the pirate discount __________________ Robert Gaskins Team Moto Inc. / ProBender.com / ProCutCNC.com rob@team-moto.com / rob@probender.com www.team-moto.com / www.probender.com / www.procutcnc.com Tel: 763.315.5019 ext. 112 Brooklyn Park, MN 55443

03-16-2009, 09:49 AM	#152 (permalink)
TMI Granite Guru Join Date: Nov 2008 Member # 122938 Location: MN Posts: 637	New 4,000 PSI Electric/Hydraulic Pump & Ram Package for the ProBender Benders Now for only $999.95 extra you can order your Pro3 or Pro4 with the 4,000 PSI Electric/Hydraulic Pump & Ram Package. So for the guys that don't want to run the bender with air you can just plug it into the 110v wall socket. With this addition we know that you cannot find a better bender on the market for the money. Period. To add the 4,000 PSI Electric/Hydraulic Pump & Ram Package your bender order? Just check it as an option that you want for your new bender. __________________ Robert Gaskins Team Moto Inc. / ProBender.com / ProCutCNC.com rob@team-moto.com / rob@probender.com www.team-moto.com / www.probender.com / www.procutcnc.com Tel: 763.315.5019 ext. 112 Brooklyn Park, MN 55443

03-16-2009, 09:33 PM	#153 (permalink)
1982cj7 Registered User Join Date: Nov 2008 Member # 123298 Location: Everett, Wa Posts: 43	I got the bender put together, i am wondering if the gap next to the die is too much? There is about 3/4" gap between the die and the arm, is this ok or should I cut down the spacers? __________________ Confidence is that feeling you have right before you fully understand the situation.

03-17-2009, 07:07 PM	#157 (permalink)
1982cj7 Registered User Join Date: Nov 2008 Member # 123298 Location: Everett, Wa Posts: 43	I am building a base for it, I will have it done before I do any bending. __________________ Confidence is that feeling you have right before you fully understand the situation.

03-18-2009, 05:32 AM	#158 (permalink)
99tantj Wheeler Join Date: May 2004 Member # 30600 Posts: 262	I may be mistaken, but it looks like you might have the ram connected to the wrong bolt. This is how I did mine. I think this is right, then again I may be the one that has it wrong. I also added a couple sleeves on both sides of the ram just to keep it centered. Last edited by 99tantj; 04-21-2009 at 07:07 AM.

03-16-2009, 10:38 PM	#154 (permalink)
99tantj Wheeler Join Date: May 2004 Member # 30600 Posts: 262	Are those the 1/2" or 5/8" arms?

03-18-2009, 12:33 PM	#160 (permalink)
99tantj Wheeler Join Date: May 2004 Member # 30600 Posts: 262	Thanks, it would look a LOT better with some tube sticking out of it.

03-18-2009, 05:57 PM	#161 (permalink)
1982cj7 Registered User Join Date: Nov 2008 Member # 123298 Location: Everett, Wa Posts: 43	I will have to switch mine, in the directions it looked like it was hooked up the way I have it. I still have to paint it yet anyway. __________________ Confidence is that feeling you have right before you fully understand the situation.

03-24-2009, 08:28 PM	#163 (permalink)
72blazer Marion Cobretti Join Date: Dec 2004 Member # 40131 Location: The Real South Texas Posts: 3,480	PM sent __________________ The Web Wheeler's '72 Motorsport Syndicate:::Edinburg TX H&H Fabrication:::Amarillo TX

03-25-2009, 07:06 AM	#164 (permalink)
TMI Granite Guru Join Date: Nov 2008 Member # 122938 Location: MN Posts: 637	PM sent back __________________ Robert Gaskins Team Moto Inc. / ProBender.com / ProCutCNC.com rob@team-moto.com / rob@probender.com www.team-moto.com / www.probender.com / www.procutcnc.com Tel: 763.315.5019 ext. 112 Brooklyn Park, MN 55443

04-01-2009, 11:18 AM	#165 (permalink)
spidr Karnage Join Date: Oct 2005 Member # 55444 Location: Vancouver Island Posts: 7,951	Pm sent. __________________ Thanks to BAILEIGH INDUSTRIAL Krush RT IFS/IRS Thanks to Epic Polymer Fox Kustoms Inc Pathmaker Productions[/color] https://www.facebook.com/KrushRacing

04-01-2009, 02:50 PM	#167 (permalink)
TMI Granite Guru Join Date: Nov 2008 Member # 122938 Location: MN Posts: 637	Spidr- I got the pipe section fixed on the website. Thanks for bringing it to my attention. __________________ Robert Gaskins Team Moto Inc. / ProBender.com / ProCutCNC.com rob@team-moto.com / rob@probender.com www.team-moto.com / www.probender.com / www.procutcnc.com Tel: 763.315.5019 ext. 112 Brooklyn Park, MN 55443

04-07-2009, 07:42 AM	#168 (permalink)
Hardstripe Registered User Join Date: Mar 2009 Member # 132080 Posts: 212	no response got ahold of him, was very helpful and answered all my questions, finished my order a second ago. Last edited by Hardstripe; 04-07-2009 at 01:47 PM. Reason: update

04-08-2009, 08:37 AM	#172 (permalink)
Sundevil Wheeler Join Date: Oct 2007 Member # 101519 Location: Tucson, AZ Posts: 153	What is the advantange of switching over to the Hydraulic system over the air/Hydraulic system? More bending power? faster? more control?

04-16-2009, 09:23 AM	#174 (permalink)
TMI Granite Guru Join Date: Nov 2008 Member # 122938 Location: MN Posts: 637	Free Bend-Tech EZ with purchase of a Pro3 or Pro4 bender is almost over. Offer End's 05/01/2009. __________________ Robert Gaskins Team Moto Inc. / ProBender.com / ProCutCNC.com rob@team-moto.com / rob@probender.com www.team-moto.com / www.probender.com / www.procutcnc.com Tel: 763.315.5019 ext. 112 Brooklyn Park, MN 55443

04-18-2009, 01:01 PM	#175 (permalink)
Hardstripe Registered User Join Date: Mar 2009 Member # 132080 Posts: 212	hey I sent you a pm concerning my order Last edited by Hardstripe; 04-18-2009 at 01:12 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode