Torchmate 2x2 setup for sale - Pirate4x4.Com : 4x4 and Off-Road Forum

Mark19382 · 06-17-2010, 01:48 PM

This decision to sell my Torchmate setup brings me great sadness as I have thoroughly enjoyed working with it over the last few months. It has exceeded all my expectations and has been a “blast” to work with! The people at Torchmate, from their sales team to their technical support team, have been great to work with. However, due to family circumstances in need to convert my garage into an apartment for my aging mother and I need to clear out all my stuff…

So here is what I have:
Torchmate 2x2 Paid 1995.00
-with water table
Torchmate machine torch holder Paid 175.00
Torchmate CADLite Paid 250.00
Torchmate Routing Package Paid 770.00
BobCAM 3-D Software Paid 495.00

Hypertherm PowerMax 45 cutter Paid 1559.00
-with hand torch
Hypertherm Machine Torch Paid 406.00
Hypertherm CNC interface cable Paid 45.00
Hypertherm FineCut Consumables Paid 75.00

Millermatic 140 + cylinder Paid 870.00

CH 60 Gal Air Compressor Paid 400.00
DeVilbiss QC3 Air Filter & Dryer Paid 151.00
Total Paid $7,191.00

I am hoping to find someone who would like the whole setup. If so, I would let everything go for only $5,500.00. I really can afford to go much lower as I now need the money to convert my garage into the apartment (carpeting, kitchen cabinets and appliances, bathroom fixtures, etc.).

I am located in West Chester, PA (about 30 minutes west of Philadelphia). If anyone has an interest, please feel free to contact me. Right now everything is still connected and fully operational for you to check out. If it helps I could spend a little time showing you some basic how-to stuff to help you get started.

Thanks for your consideration,
Mark

Arya Ebrahimi · 06-17-2010, 02:38 PM

PM Sent!

Arya Ebrahimi · 06-21-2010, 08:18 AM

Wondering if you got my PM...?

Mark19382 · 07-03-2010, 10:18 AM

Thank you everyone for your interest. I was able to sell my complete setup yesterday. Thank you Ben and best of luck with this!

cvc9216 · 07-10-2010, 03:24 PM

Thanks for the great deal Mark. I've wanted a cnc plasma forever and it would've been years before I could justify buying one otherwise. After a few days playing around with it I think I have the hang of it and it's working great. thanks again!

Manuel T. · 08-20-2010, 10:32 AM

Mark,
Do you still have Torchmate and accessories for sale ??

Call me aat 330-479-9899

Manuel
Canton, Ohio

PAToyota · 08-20-2010, 10:56 AM

Quote:

Originally Posted by Mark19382

Thank you everyone for your interest. I was able to sell my complete setup yesterday. Thank you Ben and best of luck with this!

Quote:

Originally Posted by Manuel T.

Mark,
Do you still have Torchmate and accessories for sale ??

Call me

Read much?

06-17-2010, 01:48 PM	#1 (permalink)
Mark19382 Registered User Join Date: Mar 2010 Member # 156188 Location: West Chester, PA Posts: 5	Torchmate 2x2 setup for sale This decision to sell my Torchmate setup brings me great sadness as I have thoroughly enjoyed working with it over the last few months. It has exceeded all my expectations and has been a “blast” to work with! The people at Torchmate, from their sales team to their technical support team, have been great to work with. However, due to family circumstances in need to convert my garage into an apartment for my aging mother and I need to clear out all my stuff… So here is what I have: Torchmate 2x2 Paid 1995.00 -with water table Torchmate machine torch holder Paid 175.00 Torchmate CADLite Paid 250.00 Torchmate Routing Package Paid 770.00 BobCAM 3-D Software Paid 495.00 Hypertherm PowerMax 45 cutter Paid 1559.00 -with hand torch Hypertherm Machine Torch Paid 406.00 Hypertherm CNC interface cable Paid 45.00 Hypertherm FineCut Consumables Paid 75.00 Millermatic 140 + cylinder Paid 870.00 CH 60 Gal Air Compressor Paid 400.00 DeVilbiss QC3 Air Filter & Dryer Paid 151.00 Total Paid $7,191.00 I am hoping to find someone who would like the whole setup. If so, I would let everything go for only $5,500.00. I really can afford to go much lower as I now need the money to convert my garage into the apartment (carpeting, kitchen cabinets and appliances, bathroom fixtures, etc.). I am located in West Chester, PA (about 30 minutes west of Philadelphia). If anyone has an interest, please feel free to contact me. Right now everything is still connected and fully operational for you to check out. If it helps I could spend a little time showing you some basic how-to stuff to help you get started. Thanks for your consideration, Mark

06-17-2010, 02:38 PM	#2 (permalink)
Arya Ebrahimi Zeus of the Sluice Join Date: Oct 2001 Member # 7876 Location: Rockville, MD Posts: 4,232	PM Sent! __________________ DD/Tow-rig: '06 GMC Sierra 2500HD Duramax Classic Rig: '88 FJ62, 100% stock In the weeds waiting for resurrection: '94 FZJ80, 33s, locked

06-21-2010, 08:18 AM	#3 (permalink)
Arya Ebrahimi Zeus of the Sluice Join Date: Oct 2001 Member # 7876 Location: Rockville, MD Posts: 4,232	Wondering if you got my PM...? __________________ DD/Tow-rig: '06 GMC Sierra 2500HD Duramax Classic Rig: '88 FJ62, 100% stock In the weeds waiting for resurrection: '94 FZJ80, 33s, locked

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-03-2010, 10:18 AM	#4 (permalink)
Mark19382 Registered User Join Date: Mar 2010 Member # 156188 Location: West Chester, PA Posts: 5	Thank you everyone for your interest. I was able to sell my complete setup yesterday. Thank you Ben and best of luck with this!

07-10-2010, 03:24 PM	#5 (permalink)
cvc9216 Registered User Join Date: Jan 2008 Member # 106057 Posts: 12	Thanks for the great deal Mark. I've wanted a cnc plasma forever and it would've been years before I could justify buying one otherwise. After a few days playing around with it I think I have the hang of it and it's working great. thanks again!

08-20-2010, 10:32 AM	#6 (permalink)
Manuel T. Registered User Join Date: Aug 2010 Member # 166726 Posts: 1	Mark, Do you still have Torchmate and accessories for sale ?? Call me aat 330-479-9899 Manuel Canton, Ohio