87 samurai waggy 44's Clean and built - Pirate4x4.Com : 4x4 and Off-Road Forum

rockslutscoutII · 10-06-2011, 09:21 AM

SOLD SOLD SOLD Thanks Ken for Idaho..

Im selling this samurai because i have early bronco fever.. I built this over the last 2 years my self. Took my time and did every thing the way i wanted. But i think i am one of those guys who likes to build them more than wheel them.
This is a turn key rig everything works from the heater to the wipers

1.3 about 60000 miles runs real strong for a little 4 banger
stock tranny and t case has the 6.5-1 gears ,twin sticked, and the zor offroad t case bucket
My side 2, harley 40mm carb setup. runs like fuel injection
waggy 44s front and rear with 5.13s and Aussie lockers (spare rear shafts)
4 wheel disk breaks
High steer, everything is above the leafs
braided break lines
36'' interco's 85% tread with aluminum wheels
toyota ifs power steering- stretched 12'' in the front
f-250 power steering pump
Gm 70amp alternater up grade
subaru master cylender 7/8'' piston
long slip front drive line
wrangler springs all 4 corners
heavy duty axle wrap bar
removable exo cage remove 8 grade 8 bolts to lift it off
i built the exo over the soft top but messed up the soft top in the proses. A new top will fit under the cage I have all the hardware for a soft top. Comes with bikini top.
nice seats front and rear the whole inside is clean and stock with carpet kit( needs tunes)
Everything has maybe 5 hwy miles , 3 trail rides and 3 snow trips on it
This thing has two registrations it is on non opp and also green stickered
i had all the lights working break, tail, turn, head. so if u can get it smogged it should be street legal except the mud flaps. It will not pass visual smog in Calif Im sure it will pass a sniff test though. U would need to know a guy who will do a "buddy" smog for ya Or put a stock intake and carb back on it..

I have done the Barrit trail, Rubicon and some of fordice

It drives down the road at 55mph like a Ferrari, well maybe not that good but real nice strait no wobble no pulling to one side, very good road manners. breaks work great.

Ok guys, willing to trade for some thing that i can sell for $5500-$6000. Needs to be cool though. I dont want a 1999 crown vic. Lookin for maybe hot rods or streetable built 4x you know something cool. Thanks, Mike

best to call but i will check this post everyday. Mike 530 391 8175
Cool, Ca
5500.00

just took new pic's here is the link

http://photobucket.com/sammipicks

http://photobucket.com/sammivid

snow wheelin videos for ya,,

Sand wheelin vodeo

http://s394.photobucket.com/albums/p...t=Video028.mp4

* Location: Cool

rockslutscoutII · 10-07-2011, 05:44 PM

ttt

jpuga87 · 10-07-2011, 08:22 PM

u wanna trade ? http://pirate4x4.com/forum/showthrea...hlight=samurai

rockslutscoutII · 10-08-2011, 04:40 AM

No thank's. Only trade would be for a early bronco.

rockslutscoutII · 10-08-2011, 08:04 PM

bump...

rockslutscoutII · 10-10-2011, 06:47 AM

Bump..

rockslutscoutII · 10-11-2011, 08:50 PM

and Bump...

rockslutscoutII · 10-13-2011, 06:42 AM

Bump

rockslutscoutII · 10-17-2011, 07:30 PM

price drop.,.,, bump

yotamikez · 10-17-2011, 09:53 PM

Bump. Inspiration, wish I had money lol.

rockslutscoutII · 10-25-2011, 07:48 AM

back up top,,,,

rockslutscoutII · 10-26-2011, 07:28 AM

ttt

Bogosian · 10-26-2011, 08:13 AM

nice, clean samurai.... who wouldn't rather have an early bronco, though?? early broncos are definately my favorite rigs.... just cost too much....

can build a nice yota for the price of a decent , stock bronco.

but nothing looks as good as those bronco's do when they're all done up, imo....

rockslutscoutII · 10-26-2011, 03:36 PM

they are pricey but there are a few around i have my eye on that are not to bad. Ive always wanted one and someday i will have one.

rockslutscoutII · 10-27-2011, 06:47 AM

bump

rockslutscoutII · 10-28-2011, 06:45 AM

up top...

rockslutscoutII · 10-29-2011, 09:31 PM

up top

rockslutscoutII · 11-03-2011, 08:31 PM

bump

doubleoh7 · 11-04-2011, 08:49 PM

Thanks for the great communication - bump for an awesome sammi!!

rockslutscoutII · 11-06-2011, 04:45 PM

no prob. Thanks for the bump

rockslutscoutII · 11-09-2011, 04:22 AM

ttt

rockslutscoutII · 11-11-2011, 06:55 AM

This is a bad time to sale i know, but u cant buy a new quad for $6500 ????

93_zj · 11-12-2011, 07:49 AM

Bump.

I really like the way you have the exocage setup so it can be disconnected. Do you think it is any weaker being like that instead of welded?

rockslutscoutII · 11-12-2011, 07:52 PM

Thanks 93, I wouldn't think so its held on at 8 points that are all tied to the frame. Thanks for the bump. Now some one buy this sammy!!!!

rockslutscoutII · 11-15-2011, 05:36 PM

price drop $5800.00

10-06-2011, 09:21 AM	#1 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	87 samurai waggy 44s Clean and built (NEW PIC'S and VIDEO added) ADDED) SOLD SOLD SOLD Thanks Ken for Idaho.. Im selling this samurai because i have early bronco fever.. I built this over the last 2 years my self. Took my time and did every thing the way i wanted. But i think i am one of those guys who likes to build them more than wheel them. This is a turn key rig everything works from the heater to the wipers 1.3 about 60000 miles runs real strong for a little 4 banger stock tranny and t case has the 6.5-1 gears ,twin sticked, and the zor offroad t case bucket My side 2, harley 40mm carb setup. runs like fuel injection waggy 44s front and rear with 5.13s and Aussie lockers (spare rear shafts) 4 wheel disk breaks High steer, everything is above the leafs braided break lines 36'' interco's 85% tread with aluminum wheels toyota ifs power steering- stretched 12'' in the front f-250 power steering pump Gm 70amp alternater up grade subaru master cylender 7/8'' piston long slip front drive line wrangler springs all 4 corners heavy duty axle wrap bar removable exo cage remove 8 grade 8 bolts to lift it off i built the exo over the soft top but messed up the soft top in the proses. A new top will fit under the cage I have all the hardware for a soft top. Comes with bikini top. nice seats front and rear the whole inside is clean and stock with carpet kit( needs tunes) Everything has maybe 5 hwy miles , 3 trail rides and 3 snow trips on it This thing has two registrations it is on non opp and also green stickered i had all the lights working break, tail, turn, head. so if u can get it smogged it should be street legal except the mud flaps. It will not pass visual smog in Calif Im sure it will pass a sniff test though. U would need to know a guy who will do a "buddy" smog for ya Or put a stock intake and carb back on it.. I have done the Barrit trail, Rubicon and some of fordice It drives down the road at 55mph like a Ferrari, well maybe not that good but real nice strait no wobble no pulling to one side, very good road manners. breaks work great. Ok guys, willing to trade for some thing that i can sell for $5500-$6000. Needs to be cool though. I dont want a 1999 crown vic. Lookin for maybe hot rods or streetable built 4x you know something cool. Thanks, Mike best to call but i will check this post everyday. Mike 530 391 8175 Cool, Ca 5500.00 just took new pic's here is the link http://photobucket.com/sammipicks http://photobucket.com/sammivid snow wheelin videos for ya,, Sand wheelin vodeo http://s394.photobucket.com/albums/p...t=Video028.mp4 * Location: Cool __________________ Sammi on Waggys in the works Last edited by rockslutscoutII; 05-27-2012 at 07:26 PM. Reason: add pic's

10-07-2011, 05:44 PM	#2 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	ttt __________________ Sammi on Waggys in the works

10-08-2011, 04:40 AM	#4 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	No thank's. Only trade would be for a early bronco. __________________ Sammi on Waggys in the works Last edited by rockslutscoutII; 10-08-2011 at 04:41 AM.

10-08-2011, 08:04 PM	#5 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	bump... __________________ Sammi on Waggys in the works

10-10-2011, 06:47 AM	#6 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	Bump.. __________________ Sammi on Waggys in the works

10-07-2011, 08:22 PM	#3 (permalink)
jpuga87 Registered User Join Date: May 2011 Member # 190523 Posts: 118	u wanna trade ? http://pirate4x4.com/forum/showthrea...hlight=samurai

10-11-2011, 08:50 PM	#7 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	and Bump... __________________ Sammi on Waggys in the works

10-13-2011, 06:42 AM	#8 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	Bump __________________ Sammi on Waggys in the works

10-17-2011, 07:30 PM	#9 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	price drop.,.,, bump __________________ Sammi on Waggys in the works Last edited by rockslutscoutII; 10-17-2011 at 07:31 PM.

10-17-2011, 09:53 PM	#10 (permalink)
yotamikez Registered User Join Date: Jul 2011 Member # 195143 Location: FL Posts: 29	Bump. Inspiration, wish I had money lol.

10-25-2011, 07:48 AM	#11 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	back up top,,,, __________________ Sammi on Waggys in the works

10-26-2011, 07:28 AM	#12 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	ttt __________________ Sammi on Waggys in the works

10-26-2011, 08:13 AM	#13 (permalink)
Bogosian Registered User Join Date: Sep 2011 Member # 199229 Location: paradise Posts: 187	nice, clean samurai.... who wouldn't rather have an early bronco, though?? early broncos are definately my favorite rigs.... just cost too much.... can build a nice yota for the price of a decent , stock bronco. but nothing looks as good as those bronco's do when they're all done up, imo....

10-26-2011, 03:36 PM	#14 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	they are pricey but there are a few around i have my eye on that are not to bad. Ive always wanted one and someday i will have one. __________________ Sammi on Waggys in the works Last edited by rockslutscoutII; 10-26-2011 at 03:36 PM.

10-27-2011, 06:47 AM	#15 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	bump __________________ Sammi on Waggys in the works

10-28-2011, 06:45 AM	#16 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	up top... __________________ Sammi on Waggys in the works

10-29-2011, 09:31 PM	#17 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	up top __________________ Sammi on Waggys in the works

11-03-2011, 08:31 PM	#18 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	bump __________________ Sammi on Waggys in the works

11-04-2011, 08:49 PM	#19 (permalink)
doubleoh7 Registered User Join Date: Feb 2009 Member # 130212 Posts: 38	Thanks for the great communication - bump for an awesome sammi!!

11-06-2011, 04:45 PM	#20 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	no prob. Thanks for the bump __________________ Sammi on Waggys in the works

11-09-2011, 04:22 AM	#21 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	ttt __________________ Sammi on Waggys in the works

11-11-2011, 06:55 AM	#22 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	This is a bad time to sale i know, but u cant buy a new quad for $6500 ???? __________________ Sammi on Waggys in the works

11-12-2011, 07:49 AM	#23 (permalink)
93_zj Registered User Join Date: Aug 2011 Member # 196677 Posts: 9	Bump. I really like the way you have the exocage setup so it can be disconnected. Do you think it is any weaker being like that instead of welded?

11-12-2011, 07:52 PM	#24 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	Thanks 93, I wouldn't think so its held on at 8 points that are all tied to the frame. Thanks for the bump. Now some one buy this sammy!!!! __________________ Sammi on Waggys in the works

11-15-2011, 05:36 PM	#25 (permalink)
rockslutscoutII Registered User Join Date: Feb 2002 Member # 9725 Location: Cool,Ca Posts: 386	price drop $5800.00 __________________ Sammi on Waggys in the works Last edited by rockslutscoutII; 11-17-2011 at 07:09 AM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode