#RZRKILLER is for sale - Pirate4x4.Com : 4x4 and Off-Road Forum
 
Pirate4x4.Com : 4x4 and Off-Road Forum  

Go Back   Pirate4x4.Com : 4x4 and Off-Road Forum > Vendor's Marketplace > Complete Vehicles For Sale
Notices

Reply
 
Share LinkBack Thread Tools Display Modes
Old 06-30-2014, 09:40 AM   #1 (permalink)
Rock God
 
Bent Fabrications's Avatar
 
Join Date: Feb 2007
Member # 87218
Location: KENTUCKY
Posts: 1,781
#RZRKILLER is for sale

SOLD

One of the coolest small buggies out there is for sale!

PRICE REDUCTION.. $35K negotiable based on what you want with it.

The chassis is a Cliffhanger SE built 15% smaller than normal. This was a concept vehicle designed to be small enough to run tight woods trails and hang out with SXS's yet have the crawl and climbing abilities of a buggy to go places the bigger rigs just can't go. The chassis is going to be limited to passengers under 5'10" to be comfortable and safe. This buggy is a NEW turnkey buggy completely built by Bent Fabrications.. it has been taken to KOH 2014 for display only.

If your interested, contact Tim at 859-396-4541 or send an email to [email protected]


Cliffhanger SE chassis
3.4V6 from a 1995 Chevy Camaro with several upgrades and tuned by Jim's Performance
A904 fully built with MVB and custom 2500 stahl
D300 with 4:1 LoMax gears and upgraded outputs
85 Toyota front axle with 5.29 gears (4.10's optional), dirty 30 axles and an Eaton locker
85 Toyota rear axle with 5.29 gears (4.10's optional) and spool
2" 7075 links
QA1 heims
Wilwood pedals
Fox coilovers
16x10 Trail ready beadlocks
35” Baja claws
aluminum interior panels
tinted polycarbonate body panels
Corbaeu seats recovered by Draper Customs
carbon fiber wrapped hood

Some dimensions
54" wide at the cowl
16" at the belly
23" at the rub rails
62" tall at ride height
95" wheel base
72" wide outside to outside of tires

$45K takes it home with some extras!
*price is negotiable based on what you take with it, i have several different options that will be included or left as is.

You can find TONS more info in the build thread here https://www.pirate4x4.com/forum/gene...ger-build.html









__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
What can we build for you?
Want to see what's going on in the shop?
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by Bent Fabrications; 02-12-2019 at 11:41 AM.
Bent Fabrications is offline   Reply With Quote Quick reply to this message
Old 08-05-2014, 04:06 PM   #2 (permalink)
Rock God
 
Bent Fabrications's Avatar
 
Join Date: Feb 2007
Member # 87218
Location: KENTUCKY
Posts: 1,781
We are open to trades plus cash on this.

I'd be interested in a SxS, ATV, semi built Tacoma, YJ, TJ, early bronco, blazer, first gen mustangs or Camaro's, muscle cars, rat rods, classic trucks, willys, even VW beetles or Ghias. Just something street able that doesn't need a ton of work...

Tell me what you have! Maybe we can make it work.

-Tim
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
What can we build for you?
Want to see what's going on in the shop?
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Bent Fabrications is offline   Reply With Quote Quick reply to this message
Sponsored Links
Old 08-13-2014, 03:49 AM   #3 (permalink)
Registered User
 
knaffie's Avatar
 
Join Date: May 2005
Member # 48084
Location: I live in a van down by the river
Posts: 4,411
Blog Entries: 1
^^ reported spam
knaffie is offline   Reply With Quote Quick reply to this message
 
Old 08-25-2014, 12:37 PM   #4 (permalink)
Zeus of the Sluice
 
lil,yota's Avatar
 
Join Date: Nov 2007
Member # 102395
Location: At the Lab
Posts: 2,904
I remember seeing this at KOH. Looked like a blast.
__________________
My Dream Build

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.



If you were twice as smart you would still be stupid!



But, as with most evil people, they live unnaturally long lives.

Dr Danger
lil,yota is offline   Reply With Quote Quick reply to this message
Old 12-01-2014, 01:46 PM   #5 (permalink)
Rock God
 
Bent Fabrications's Avatar
 
Join Date: Feb 2007
Member # 87218
Location: KENTUCKY
Posts: 1,781
Want a bad ass rig for Christmas?

I just reduced the price for some lucky person to snag this thing up in time to get it under the tree.

Negotiable at $35K pending extras.



Contact [email protected] for details or questions





.
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
What can we build for you?
Want to see what's going on in the shop?
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Bent Fabrications is offline   Reply With Quote Quick reply to this message
Old 02-02-2015, 11:15 AM   #6 (permalink)
Registered User
 
Join Date: Feb 2013
Member # 259753
Posts: 1
trade

will i have a 2013 ford edge limited alwheel drive with 28000 miles on it and still under warranty i will trade for your crawler ? if so you can call me at 360-708-9133 and i will send pic
corncobb is offline   Reply With Quote Quick reply to this message
Old 02-14-2015, 08:01 PM   #7 (permalink)
Registered User
 
Join Date: Apr 2008
Member # 113094
Location: Moberly mo.
Posts: 152
Any videos of it in action??
noracin is offline   Reply With Quote Quick reply to this message
Old 02-20-2015, 12:39 PM   #8 (permalink)
Registered User
 
Join Date: Jun 2003
Member # 20490
Location: Camden, SC
Posts: 975
Send a message via AIM to clemsonjeep
Quote:
Originally Posted by noracin View Post
Any videos of it in action??
x2
__________________
'88 Sammy
91 1.6L 8v EFI w/ K03 Turbo
03-72LE 4 Speed Auto / 6.5 tcase
Toy's cyro'd 5.29s ARB HP front
Elocker rear w/ cryo'd lock collar & side gears
Trunnion bearing eliminator
Longfields/chromo hub gears
4 link air shocks front / 4 link air shocks rear
39 BFG Reds
Raceline Monsters
clemsonjeep is offline   Reply With Quote Quick reply to this message
Old 03-05-2015, 06:40 AM   #9 (permalink)
Registered User
 
KaGe13's Avatar
 
Join Date: Oct 2014
Member # 509578
Location: Cornfield in Southern Indiana
Posts: 34
Curious why you went with the 3.4 and not the later 3.8? Size/weight?
__________________
TJ -40's, 60's, 3lnk fr, 4lnk r, KingCO, 113"WB, 26"F2S, etc
KaGe13 is offline   Reply With Quote Quick reply to this message
Old 03-11-2015, 11:41 AM   #10 (permalink)
Rock God
 
Bent Fabrications's Avatar
 
Join Date: Feb 2007
Member # 87218
Location: KENTUCKY
Posts: 1,781
Quote:
Originally Posted by KaGe13 View Post
Curious why you went with the 3.4 and not the later 3.8? Size/weight?
The 3.8 camaro motor is actually a different motor completely. one of the biggest turnoffs is the odd shape of the intake. It kinda sucks to deal with. I got a killer deal on a wrecked camaro when scouting around for a 3200 or 3400 from a car, and discovered the Camaro block is a better setup since the motor mounts were on the side of the block as well as the starter was in the correct spot to work with the trans, so we rolled with it.

If I had it to do over, I would have probably looked for a Buick SC 3800 and went that route instead. simply for the aftermarket support and available power adder options to be there if I wanted to persue them. Cheaper bang for the buck.
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
What can we build for you?
Want to see what's going on in the shop?
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Bent Fabrications is offline   Reply With Quote Quick reply to this message
Old 03-14-2015, 07:43 PM   #11 (permalink)
Registered User
 
Join Date: Nov 2011
Member # 204558
Posts: 1,346
What is the total weight?
Jac0b is offline   Reply With Quote Quick reply to this message
Old 03-16-2015, 02:09 PM   #12 (permalink)
Rock God
 
Bent Fabrications's Avatar
 
Join Date: Feb 2007
Member # 87218
Location: KENTUCKY
Posts: 1,781
We never weighed it complete.. but I'll be bringing it back to the shop in a few weeks and plan to hit the scales with it on the way. I'll post up in the build thread when I know.. Looks like It's going to TX soon.

Tim
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
What can we build for you?
Want to see what's going on in the shop?
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Bent Fabrications is offline   Reply With Quote Quick reply to this message
Old 04-18-2015, 11:46 PM   #13 (permalink)
Registered User
 
Join Date: Jul 2013
Member # 339802
Location: Colorado
Posts: 22
Is this still for sale?
jammer NR is offline   Reply With Quote Quick reply to this message
Old 04-20-2015, 02:10 PM   #14 (permalink)
Rock God
 
Bent Fabrications's Avatar
 
Join Date: Feb 2007
Member # 87218
Location: KENTUCKY
Posts: 1,781
The original investor has paid it off and has it to wheel some. He may still consider selling pending the offer.
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
What can we build for you?
Want to see what's going on in the shop?
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Bent Fabrications is offline   Reply With Quote Quick reply to this message
Old 04-21-2015, 07:55 AM   #15 (permalink)
Rock God
 
Bent Fabrications's Avatar
 
Join Date: Feb 2007
Member # 87218
Location: KENTUCKY
Posts: 1,781
We did get to finally weigh this thing. scale is in the pic.

__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
What can we build for you?
Want to see what's going on in the shop?
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Bent Fabrications is offline   Reply With Quote Quick reply to this message
Old 04-21-2015, 12:37 PM   #16 (permalink)
Registered User
 
Join Date: Nov 2011
Member # 204558
Posts: 1,346
Thank you. Post up whatever they decide.
Jac0b is offline   Reply With Quote Quick reply to this message
Old 06-13-2015, 01:46 PM   #17 (permalink)
Registered User
 
Join Date: Mar 2012
Member # 214242
Location: Beckley
Posts: 28
Hey just wondering if you still have this unit???
controlsengineer is offline   Reply With Quote Quick reply to this message
Old 06-15-2015, 10:54 PM   #18 (permalink)
Registered User
 
Join Date: Apr 2007
Member # 89535
Location: Hot Springs, AR
Posts: 1,762
Quote:
Originally Posted by controlsengineer View Post
Hey just wondering if you still have this unit???
It does appear to be for sale.

https://www.pirate4x4.com/forum/vehic...rzrkiller.html
__________________
NRB - ...I'd be happy as a fagot in a peter tree to buy this from you.
Jordan7118 is offline   Reply With Quote Quick reply to this message
Old 09-07-2015, 11:37 AM   #19 (permalink)
Registered User
 
Join Date: Mar 2012
Member # 214242
Location: Beckley
Posts: 28
Take a 2015 RZR Desert Edition on trade?
__________________
2010 Jeep JK 4 Door, 5" Trail Master Lift, 37x13.50R20 Toyos
Detroit Lockers Front & Back w/ 5.13's
controlsengineer is offline   Reply With Quote Quick reply to this message
Old 07-27-2017, 12:31 PM   #20 (permalink)
Registered User
 
Join Date: Jul 2017
Member # 774449
Posts: 7
Tried to send a PM, your inbox is full.
hubbazoot is offline   Reply With Quote Quick reply to this message
Old 07-27-2017, 03:10 PM   #21 (permalink)
Rock God
 
Bent Fabrications's Avatar
 
Join Date: Feb 2007
Member # 87218
Location: KENTUCKY
Posts: 1,781
Quote:
Originally Posted by hubbazoot View Post
Tried to send a PM, your inbox is full.
send an email to [email protected]abrications.com if you need to reach me.
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
What can we build for you?
Want to see what's going on in the shop?
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Bent Fabrications is offline   Reply With Quote Quick reply to this message
Old 02-12-2019, 11:15 AM   #22 (permalink)
Registered User
 
Join Date: Aug 2018
Member # 855116
Posts: 11
Oh man...
Manuel Hidalgo is offline   Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Pirate4x4.Com : 4x4 and Off-Road Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.

** A VERIFICATION EMAIL IS SENT TO THIS ADDRESS TO COMPLETE REGISTRATION!! **

Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 10:27 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 ©2011, Crawlability, Inc.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.