#1
·
May 23, 2013
been building this buggy slowly.
its half formula offroad and half rock racing buggy.
it has.
bbc 454 hydroller aluminium head. mpfi engine ~500hp
th400 full manual valvebody+ultrabell
np205 twin sticked
dodge d60 front and 14b rear.
saw 14" shocks and profender bump stops.
4-link front/rear
started placing engine and axels into jig table and it was tube time
128 KB
Views: 9,491
136.8 KB
Views: 9,113
53 KB
Views: 9,085
87.4 KB
Views: 9,139
94.5 KB
Views: 9,166
See less
See more
5
#2
·
May 23, 2013
more chassis work
81 KB
Views: 9,085
84.1 KB
Views: 9,060
73.6 KB
Views: 8,997
75 KB
Views: 9,028
82.2 KB
Views: 9,037
#3
·
May 23, 2013
did some link tabs and mounted shocks and bump stops. got it in to rolling state.
60.8 KB
Views: 8,926
60.6 KB
Views: 8,949
63 KB
Views: 9,115
64 KB
Views: 9,523
66.6 KB
Views: 8,929
#4
·
May 23, 2013
m
73.1 KB
Views: 8,877
71.1 KB
Views: 8,884
67.2 KB
Views: 8,945
#6
·
May 23, 2013
did steering arms for front/shaved some of the 14b and fabricated covers for both axels.
119.8 KB
Views: 8,830
129.8 KB
Views: 8,790
117.7 KB
Views: 8,825
62.6 KB
Views: 8,764
#13
·
Jun 3, 2013
What did you use for the diff fill holes? Please say its at my local ace hardware
1
Reply
#7
·
May 23, 2013
did get some goodies from over seas.
67.2 KB
Views: 8,754
77.1 KB
Views: 8,795
78.2 KB
Views: 8,764
#8
·
May 23, 2013
today finished radiator mounting.
50.9 KB
Views: 8,774
131.2 KB
Views: 8,729
65.7 KB
Views: 8,720
56.6 KB
Views: 8,764
#14
·
Jun 3, 2013
nice hi steer arms :smokin: did you make them so you can run a bolt through the stock mount?
#18
·
Jun 4, 2013
no they dont have this extra support, maybe ad it later if i have any strenght issues
0
Reply
#20
·
Jun 7, 2013
battery mount ready to be installed in to chassis
62.6 KB
Views: 7,753
65.4 KB
Views: 7,601
58.1 KB
Views: 7,542
#22
·
Jun 9, 2013
made transmisson cooler box from two mitsubishi oil coolers and spal fan.
62.6 KB
Views: 7,295
57.4 KB
Views: 7,261
#25
·
Jun 11, 2013
made mount for rear winch
57.6 KB
Views: 6,997
67.1 KB
Views: 7,001
#26
·
Jun 20, 2013
non vented rotors
26lbs to 13lbs
55.9 KB
Views: 3,988
144.2 KB
Views: 3,968
#27
·
Jun 20, 2013
Can you post up some details on this set up?
What is the rotor off of?
WilWood Dyna Lite caliper?
Any idea how much weight it saved?
#28
·
Jun 20, 2013
stock chevy d60 rotor
dynalite caliber
13lbs/rotor + difference in dynalite and stock caliber
0
Reply
#29
·
Jun 20, 2013
Plans for races like KOV? It looks like it would be very competitive there or at the Italian WTI competitions. Looks great!
#30
·
Jun 20, 2013
we have similar small competitions im planning to drive. looped offroad track and 1 hour time to make as many laps as you can . and all racers start at same time.like motocross.
and maybe some local Formula offroad races too.
0
Reply
#31
·
Jun 26, 2013
(Edited)
made mount plates for front calibers.
made disk as small as i could to make room for 15" wheel. ended to be 12.3" dia and 0.40" disk width
65.2 KB
Views: 3,628
66.1 KB
Views: 3,621
137.9 KB
Views: 2,838
136.6 KB
Views: 2,848
#33
·
Jul 10, 2013
(Edited)
made mounts for rear disk calibers.
52.5 KB
Views: 3,449
48.4 KB
Views: 3,445
58.3 KB
Views: 2,850
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.