Pirate4x4.Com : 4x4 and Off-Road Forum

Pirate4x4.Com : 4x4 and Off-Road Forum (https://www.pirate4x4.com/forum/index.php)
-   General 4x4 Discussion (https://www.pirate4x4.com/forum/forumdisplay.php?f=16)
-   -   Fishmouth Project-tt-hilux Chassis Re Purposed (https://www.pirate4x4.com/forum/showthread.php?t=2354066)

DickK 07-08-2016 06:49 PM

Mid Engine Toyota Cab 4400 build in PDX
 
I originally started posting the rebuild of this chassis on the old build page but feel its in the wrong spot. Theres no toyota to this build besides the cab and doors and will fit in much better in general. Ill start off by saying all the changes were by choice, not because of mistakes or a lack of quality. This thing was dialed for what it was first built to do. I just happen to want to go a different direction and was willing to spend the money and time to do that. Some of the post will be duplicate of what I have posted on the old page and new pics will be posted regularly with updates. A big thank you to everyone involved and to Austin down in Utah who allowed me to buy the cab and chassis from him. And to Cornfed and his son for all there help, skill and knowledge If you would like to check out the tread started by fishmouth in 2007 the link is

https://www.pirate4x4.com/forum/toyot...-tt-hilux.html

I would like to think we have not skimped on quality parts or time with this build. the goal is to race KOH 2017.

Motor is a 6.2l L92
Kevco oil pan
Trans is a 60L80 with ford 205 case
Radesigns 6l80 shifter with tap shift
Fox coils and Bypass Front and rear
Wilwood Rotors and 6 piston Calipers
Full PSC steering system put together by Randy from Bomber, Big thanks to him for the help and advice
CBR radiator with Heat exchanger to cool the motor
CBR cooler for trans
JAZZ man o' war fuel cell
Corbeau Pro Series Kevlar Blend seats
Ruff stuff trailing arms, 1.25 heims, link towers, and coil over bypass mounts
Front axle will be Ruff Stuff custom 9" 3.5 tube 3/8 wall housing with flipped center section, spydertrax pro series C and knuckles. High Pinion 40 spline Gearworks drop out!
Rear will be a Ruff Stuff custom length 9" 3.5 tube 3/8 wall housing with Flipped center, Torq 40 spline spindles, Sunfire off road Aluminum hubs, with High Pinion 40 spline Gearworks drop out
Sway bar will be Ruff stuff
motor mounts are from Ruffstuff
Axle side link mounts are from Jimmys 4x4
Gauges are from Speedhut
205 case mount is from Brave motorsports along with the steering arms
Trail ready wheels

http://i1016.photobucket.com/albums/...pspr4u9nvc.jpg
http://i1016.photobucket.com/albums/...pspp5ezr5m.jpg
http://i1016.photobucket.com/albums/...psgs2f9zpp.jpg
http://i1016.photobucket.com/albums/...pse7twmrsq.jpg
http://i1016.photobucket.com/albums/...psbzpuu6zz.jpg
http://i1016.photobucket.com/albums/...psh0pa97uk.jpg
http://i1016.photobucket.com/albums/...psutwqumbw.jpg

DickK 07-08-2016 06:54 PM

http://i1016.photobucket.com/albums/...pskambak5o.jpg
Torq 40 spline spindles for the rearhttp://i1016.photobucket.com/albums/...psrwaqscu0.jpg
Rad Design 6l80 tap shift set uphttp://i1016.photobucket.com/albums/...pskcxkkhvc.jpg
http://i1016.photobucket.com/albums/...ps3kxdhqym.jpg
http://i1016.photobucket.com/albums/...psl8vh0igu.jpg
PSC steering sent by Bomber Fabhttp://i1016.photobucket.com/albums/...ps6xea2lwe.jpg
http://i1016.photobucket.com/albums/...psl1aq5hzj.jpg
http://i1016.photobucket.com/albums/...psial9eaqm.jpg
http://i1016.photobucket.com/albums/...psahqaxa0z.jpg

DickK 07-08-2016 07:02 PM

Corbeau Seats ordered from Superior Off Road http://i1016.photobucket.com/albums/...psyksrk1to.jpg
http://i1016.photobucket.com/albums/...psnxoxyz2h.jpg
PCI supplied the Radios, gps and race air http://i1016.photobucket.com/albums/...pslkyvrvqp.jpg
http://i1016.photobucket.com/albums/...psby6cpoha.jpg
http://i1016.photobucket.com/albums/...psjnkkdceu.jpg
There will be 2 Odyssey 925 with metal jackets [URL=http://s1016.photobucket.com/user/Richard_Eilenberger/media/Mobile%20Uploads/IMG_0333_zpsc1dsx7pj.jpg.html]http://i1016.photobucket.com/albums/...psc1dsx7pj.jpg[/URL
CBR rad ordered from Bomber fab with heat exchanger for oil coolinghttp://i1016.photobucket.com/albums/...pseu3cmjam.jpg
Drop outs from Gearworks ordered threw Bomber Fab 40spine from and rear with spoolshttp://i1016.photobucket.com/albums/...ps1paztaaf.jpg
http://i1016.photobucket.com/albums/...pscdfcnmyi.jpg
http://i1016.photobucket.com/albums/...pspx8uz8vm.jpg

DickK 07-08-2016 07:11 PM

Couple new tubes to had strength to the front end and new 1.5 windshield bars http://i1016.photobucket.com/albums/...psiw7xqbbl.jpghttp://i1016.photobucket.com/albums/...psvcitfs88.jpg
With the windshield bars came a new 1.75 dash bar
http://i1016.photobucket.com/albums/...ps1hnv9i3w.jpg
1.5" rear tube was cut out and 1.75" put in http://i1016.photobucket.com/albums/...psednmpdko.jpg
Drivers seat mounted http://i1016.photobucket.com/albums/...psjb8hkwzq.jpg
http://i1016.photobucket.com/albums/...psr7hjtlyl.jpg
Front axle upper link mounts http://i1016.photobucket.com/albums/...pskbguakfq.jpg
http://i1016.photobucket.com/albums/...psyfwpih1n.jpg
Rad mounted http://i1016.photobucket.com/albums/...pskhboxwyc.jpg
http://i1016.photobucket.com/albums/...pss9uzr6wp.jpg

DickK 07-08-2016 07:16 PM

http://i1016.photobucket.com/albums/...psmlfu1egy.jpg
The start of the new rear hoop http://i1016.photobucket.com/albums/...psnniwxthq.jpg
http://i1016.photobucket.com/albums/...psubtrlosx.jpg
http://i1016.photobucket.com/albums/...ps2vnqpb5u.jpg
Still waiting on the actually axle housings so the dash and floor as started finally fitment of the tunnel will be done soon and driver side dash will be finished when Brake master and Drivers gps arrives http://i1016.photobucket.com/albums/...pskjdwsft8.jpg
http://i1016.photobucket.com/albums/...psdz1dpkwd.jpg
http://i1016.photobucket.com/albums/...psixxbfyih.jpg

Rooster831 07-08-2016 08:04 PM

pure badass

mechanicalmongoose20 07-08-2016 08:15 PM

Mother-fuckin-subbed!!! :smokin:

mcutler1 07-08-2016 08:44 PM

Subbed, I have a similar build but front engine/single shock. Looking good!

Matt

clemsonjeep 07-08-2016 09:34 PM

Always top notch work...looking forward to seeing this blasting through the whoops/rocks!

xj9140 07-08-2016 10:29 PM

Wow, cool

TRD 07-08-2016 10:37 PM

I've drooled over this rig for years!! So awesome to see it's getting finished and raced! :smokin:

camo 07-10-2016 08:09 PM

I recently asked Trout what happened to this rig, stoked to see it coming to life.:smokin:

slravene 07-11-2016 07:54 AM

sweet mother of god

Appntr 07-11-2016 08:52 PM

Fuck...yes

BigBlue&Goldie2 07-11-2016 09:56 PM

I'm moist. :homer:

supersize75k5 07-12-2016 12:35 PM

What model pn from kevko is that? looking on their site and curious if it will fit where my current kevko pan is and add some more capacity.

erictylers1 07-12-2016 12:39 PM

1 Attachment(s)
Thought I was handy, but I don't have skills looking at this work. Sick build!!!

DickK 07-12-2016 06:46 PM

Quote:

Originally Posted by supersize75k5 (Post 37496826)
What model pn from kevko is that? looking on their site and curious if it will fit where my current kevko pan is and add some more capacity.

Ill look the part number up when I get home, but it was a custom 5" deep kevco built for a rear engine application.

DickK 07-13-2016 12:24 PM

1 Attachment(s)
New delivery today, waiting in housing, hubs and unit bearings then this thing can be a roller

DickK 07-13-2016 09:58 PM

1 Attachment(s)
3" by 16" bypass and 2" by 14" coil over waiting on the front bypass and the bumps but happy to have these things:grinpimp:

YROC FAB. 07-13-2016 11:12 PM

Lookin good man.:smokin: I cant wait to see it finished at koh. Hope to have my single seater out there. Im glad you posted a new dedicated thread for it. It was nice to meet you Richard.

Original thread>https://www.pirate4x4.com/forum/toyot...-tt-hilux.html

3rd owner thread>https://www.rme4x4.com/showthread.ph...ggy&highlight=

CORNFED 07-14-2016 12:23 PM

Quote:

Originally Posted by supersize75k5 (Post 37496826)
What model pn from kevko is that? looking on their site and curious if it will fit where my current kevko pan is and add some more capacity.

The pan is 19.5 x 8.5 and 4.75 deep.

matzell 07-14-2016 04:59 PM

Good looking build. I think you will like the drivetrain, I know I do in my 4500 car. We need more Toyota's and other vehicle based cars out there.

bark beetle 07-14-2016 06:59 PM

I like where this is headed.

DickK 07-17-2016 07:30 PM

These showed up while we were out of town racing will get some better pics tomorrow big progress coming soon :grinpimp:
http://i1016.photobucket.com/albums/...psawx2apin.jpg
http://i1016.photobucket.com/albums/...psiprqmiak.jpg


All times are GMT -7. The time now is 05:59 AM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 ©2011, Crawlability, Inc.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.