thick clocking ring - Pirate4x4.Com : 4x4 and Off-Road Forum
 
Pirate4x4.Com : 4x4 and Off-Road Forum  

Go Back   Pirate4x4.Com : 4x4 and Off-Road Forum > General Tech > General 4x4 Discussion
Notices

Reply
 
Share LinkBack Thread Tools Display Modes
Old 02-20-2010, 06:30 PM   #1 (permalink)
Registered User
 
Join Date: Oct 2006
Member # 81214
Location: Lanna, Jawja
Posts: 16,105
thick clocking ring

who makes a 1" thick clocking ring for a 300?
Never Monday is offline   Reply With Quote Quick reply to this message
Old 02-20-2010, 09:27 PM   #2 (permalink)
Zeus of the Sluice
 
rockthedog's Avatar
 
Join Date: May 2003
Member # 19510
Location: vacaville ca
Posts: 3,587
Blog Entries: 1
what adapter are you using? if it's AA just drill it out
Attached Images
 
__________________
77fj40, 1 TON

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
530-268-9494

tlca# 12281
semi_budget 1ton build

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


linking the rear

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
rockthedog is offline   Reply With Quote Quick reply to this message
Sponsored Links
Old 02-21-2010, 05:42 AM   #3 (permalink)
Registered User
 
Join Date: Oct 2006
Member # 81214
Location: Lanna, Jawja
Posts: 16,105
it's not on an adapter. Just need an inch to mate it. All the other rings are too thin.

anyone have a cad drawing of the bolt pattern?

Last edited by Never Monday; 02-21-2010 at 05:43 AM.
Never Monday is offline   Reply With Quote Quick reply to this message
 
Old 02-21-2010, 11:11 AM   #4 (permalink)
Registered User
 
mattamd_xp's Avatar
 
Join Date: Nov 2008
Member # 124054
Location: Mass
Posts: 616
http://www.trailslesstraveled.com/re...transfer-case/

You can pull the bolt pattern for the transfer case off these
mattamd_xp is offline   Reply With Quote Quick reply to this message
Old 02-21-2010, 11:25 AM   #5 (permalink)
Registered User
 
Join Date: Oct 2006
Member # 81214
Location: Lanna, Jawja
Posts: 16,105
Quote:
Originally Posted by mattamd_xp View Post
http://www.trailslesstraveled.com/re...transfer-case/

You can pull the bolt pattern for the transfer case off these
WOW...that's the shit
Never Monday is offline   Reply With Quote Quick reply to this message
Old 02-21-2010, 12:53 PM   #6 (permalink)
Registered User
 
Join Date: Sep 2005
Member # 54349
Location: Jackson NJ
Posts: 732
Advance adapters is aprox. 1 ". The kit comes with a longer input shaft to assure full engagement.
__________________
Team Quadratec Stock Mod #832 Special thanks to our sponsors:
Quadratec.com ,Rausch Creek offroad park,Tom woods Drive Shafts, Spidertrax, Mastercraft,Bfgoodrich,Ramsey, Extreme Axle Sales.com, KC Hilites, HI-9, CTM, Bushwacker, Trailready
Shram is offline   Reply With Quote Quick reply to this message
Old 02-21-2010, 01:15 PM   #7 (permalink)
Registered User
 
Join Date: Oct 2006
Member # 81214
Location: Lanna, Jawja
Posts: 16,105
Quote:
Originally Posted by Shram View Post
Advance adapters is aprox. 1 ". The kit comes with a longer input shaft to assure full engagement.
I got the input from a calrocks guy. I get over an inch, probably close to 1.5" of engagement.


I'm hitting the seal/bearing retainer on the back of the trans with my current .750 ring. Theres a gap of 1/8 - 3/16's between the trans and ring. Going to a 1" ring will get the bearing retainer off of the trans, and still keep good engagement.
I found Novac's at 7/8" it would be nice to have the 1/8" cushion

Last edited by Never Monday; 02-21-2010 at 01:15 PM.
Never Monday is offline   Reply With Quote Quick reply to this message
Old 02-22-2010, 09:14 AM   #8 (permalink)
Registered User
 
Join Date: Jul 2001
Member # 6208
Location: north slo county, Calif.
Posts: 1,133
A lot of our Atlas applications require a 1" spacer under part # AS-0404.
http://advanceadapters.com/product/2...ER-SPACER.html

It is normally required for the cherokee aw4 that has a positive stickout past the edge of the adapter and cannot be cut flush do to lack overall splines. Although not designed as a clocking ring, It does have the index lip which a lot guys over look its importance. You could use a gasket as a template to drill out your desired clocking
Vic
slo-vic is offline   Reply With Quote Quick reply to this message
Old 02-22-2010, 03:05 PM   #9 (permalink)
Registered User
 
Join Date: Oct 2006
Member # 81214
Location: Lanna, Jawja
Posts: 16,105
thanks Vic
i'm going to try it with a .250 spacer added on the tcase side first.
Never Monday is offline   Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Pirate4x4.Com : 4x4 and Off-Road Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.

** A VERIFICATION EMAIL IS SENT TO THIS ADDRESS TO COMPLETE REGISTRATION!! **

Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 08:39 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 ©2011, Crawlability, Inc.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.