Pirate4x4.Com : 4x4 and Off-Road Forum - View Profile: 66CJdean
 
Pirate4x4.Com : 4x4 and Off-Road Forum  

Go Back   Pirate4x4.Com : 4x4 and Off-Road Forum > Members List
Notices

66CJdean 66CJdean is offline

Registered User

Visitor Messages

Showing Visitor Messages 21 to 26 of 26
  1. 66CJdean
    05-14-2009 07:51 AM - permalink
    66CJdean
    The mag runflat is to wide. You need to cut it down to 6.750" or even a little less to get the wheel to come all the way together. 6.5" would even be great with those so you know that you will get the two halfs together to seal the oring. I am just getting started on a new batch of pvc runflats this week so let me know if that is the route you need to go.

    Dean
  2. cobra56889
    05-13-2009 10:18 PM - permalink
    cobra56889
    iam trying to mount a 44x19.5x16.5 Pitbull rocker on a recentered H-1 wheel with the magnesium centers. And no matter what I do I cant get them to stop leaking air. I have checked for rust around the oring area I have soaped the bead to try and make it go to geather better and iam not having any luck. I measures the PVC inserts in my 44inch TSl's and they are a little shy of 6 3/4 inches wide where as the magnesium is 7 inches wide so iam wondering if thats my problem if so I guess iam going to have to get another set of inserts. for my pitbull rockers.

    Thanks in advance

    Lane Minchew
  3. 4skinner
    04-16-2009 12:19 PM - permalink
    4skinner
    hey Dean its Jeremy at Dave's offroad checking on that blank 60 shaft.
    thanks
  4. Ugly jeep
    03-19-2009 05:20 PM - permalink
    Ugly jeep
    I am looking for info. on cryo treating one long and one short ouverson cromo 16 spline axles with ujoints. All will be new. What is the cost for that and what kind of strength increase can be expected?
  5. 66CJdean
    08-25-2008 12:22 PM - permalink
    66CJdean
    It is pretty streigh forward. The bottom of the tub will give the amount of room you need for the lower section and the top sections you just leave long until you set the tub on. At that point you can figure where the tub fits best on the frame so you can then figure where the ends of the frame needs to be and thus spring hangers and such. I used 2x4x.120 and think that is plenty strong. I wheel the hell out of it and now my friend has it and wheels the hell out of it with no problems to date with about 10 years of wheeling. I am going to build another this winter so maybe I'll take more care in "how to" since I get this question about once a year since building it.
  6. ryankalel
    08-24-2008 08:50 PM - permalink
    ryankalel
    I am thinking of welding a jeep frame and ran across your posting. Can you give me any more advice or details of the process? Thanks

About Me

  • About 66CJdean
    Company Name
    Performance Cryogenics and Kickass Offroad
    Location
    Lincoln, Ca
    Vehicle(s)
    67 cj5, 51 willie's overland
  • Signature
    [url]WWW.PCRYO.COM[/url]
    Deep Cryogenic Tempering Service
    [b][SIZE="5"]Find all my products at[/SIZE][/b]
    [url]www.KICKASSOFFROAD.COM[/url]
    [b][SIZE="4"]916-434-6978
    Custom Sway Bars and Axles built to order. [/SIZE][/b]
    [b][SIZE="5"]Got 40 spline? I have the hubs, spindles, and axles you need to kickass![/SIZE][/b]
    Custom Hummer wheels and centers
    Axle Resplining

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 01-28-2020 12:09 PM
  • Join Date: 05-19-2000

Friends

Showing Friends 1 to 10 of 12

Mentions

07-29-2019
08:44 PM - Flexy Flatty mentioned 66CJdean in post Full Floater Axle housing Jig
66CJdean I really need tho...
06-01-2018
09:29 AM - MNorby mentioned 66CJdean in post MNorby's Goat Ibex chassis build
...on to get cryo'd by 66CJdean at Performance Cryog...
09-15-2016
11:31 AM - 93_Fummins mentioned 66CJdean in post Axle shorten/re-spline recommendations
...o hijack.... But, 66CJdean, are you the one who...

Quotes

06-19-2018
06:46 PM - 66CJdean quoted Wubsor in post 40 Spline Spindles, Hubs & Stubs!
:eek: Does anyone still ...
01-12-2018
05:58 PM - CJ68 quoted 66CJdean in post Full Floater Axle housing Jig
I sure do and have quite a se...
12-06-2017
09:13 AM - CJ68 quoted 66CJdean in post Full Floater Axle housing Jig
We just made up another batch...
05-08-2017
07:26 PM - 66CJdean quoted WideOpenDesign in post 14 Bolt Steering Axle Build
We don't offer any kind of 100% cus...
02-01-2017
11:14 AM - 66CJdean quoted shaggy10000 in post Custom Axles
What blank do you use for custom...
10:40 AM - 66CJdean quoted shaggy10000 in post Custom Axles
What blank do you use for custom...
01-05-2017
02:00 PM - Blue Devil Toyota quoted 66CJdean in post Sway Bar Tech???
This is our DIY 32 spline and...
01-14-2016
01:14 PM - fordnut quoted 66CJdean in post Full Floater Axle housing Jig
They are available and they a...
11-13-2015
02:04 PM - 66CJdean quoted iwannabemro in post 40 Spline Spindles, Hubs & Stubs!
Why not use these- Axle Flange, ...
09-25-2015
03:40 PM - jrad12381 quoted 66CJdean in post Ultra 4 front axle shaft options
There are many grades of 4340...

All times are GMT -7. The time now is 11:51 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 ©2011, Crawlability, Inc.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.