|04-06-2017 11:16 AM|
|04-06-2017 11:15 AM|
|04-06-2017 09:51 AM|
Dana 60 pinion cover
can you quote me on the cost of QTY 2 machined pieces to make a Dana 60 pinion guard (Mild steel) or what you recommend. I just want to get the block of metal machined and I can take care of the rest. block of 1in machined to fit over the pinion then machined in the back to fit over the oil passage. I can take care of the drilling and tapping and also cutting it in half. Then I can bend up some plate and weld it to it. i can get you more specific measurements and also a drawing if we go forward with it.
|03-18-2017 06:32 PM|
|enginetech||Any progress on the 47 spline drive slugs for 05 up Super Duty UB's?|
|01-24-2017 09:25 AM|
|01-21-2017 02:54 PM|
|enginetech||Did you figure out if you could make drive slugs for 05 up super duty UB's for 47 spline ouverson axles?|
|12-13-2016 09:36 AM|
Blind female is a particularly long setup. Shoot us a drawing, with all specs, and we can get a quote. Need specs on splines, pressure angle etc.
|12-13-2016 09:32 AM|
|12-10-2016 08:47 AM|
|12-10-2016 08:46 AM|
|12-09-2016 06:33 PM|
|enginetech||Looking for drive slugs for 05 up super duty Dana 60 to fit ouverson 47 spline axles|
|10-31-2016 10:11 PM|
|Diablo Blanco||Are you up for making a steering stem for a motorcycle?|
|10-28-2016 10:12 PM|
|ltrail||Approximate cost to shorten and respline a pair of shafts?|
|09-08-2016 04:18 PM|
|Brian Ellinger||As youve noticed, we dont post up what we're doing for others! Be assured complete confidentiality!|
|08-26-2016 04:38 PM|
|Brian Ellinger||happy to quote that new project. Need production or prototype before production, we can do it|
|04-28-2016 09:31 AM|
|Brian Ellinger||using this forum correctly|
|06-02-2015 12:22 PM|
Custom bore size Full Float rings. These are for a Dana 44 6 bolt spindle. These are for a ford 9" rear axle, we can then cut double spline 31spline to Dana 44 30 spline axle shafts. We'll be releasing bolt on full float adapter flanges shortly to convert any big bearing or small bearing ford 9" rear axle to full float as well! This even allows an easy way to convert to a Chevy or Toyota 6on 5.5 bolt pattern!
We've been making this style ring for well over 12 years! Frontrangeoffroadfab.com Diamondaxle.com
|05-05-2015 02:57 PM|
I need a couple shims made. I can send 1 as a template. both need to be machined at a different angle.
These are specifically for the 5-bolt 1979 Ford F250 Dana 44 knuckle and are currently unavailable.
|05-19-2014 01:16 PM|
Thanks to our new customers!
As for the D300 output, just not enough interest at this time.
|04-30-2014 06:23 PM|
|04-10-2014 07:30 PM|
Quote for resplining two long side ford 60 shafts after taking off about 4". Both 35 spline, one alloy and one stock. They will be marked for you to cut, and then spline. I dont have anything that can cut that clean.
|03-24-2014 11:34 AM|
|Brian Ellinger||We can do the d300 front output machining. To make things less costly, Id like to build a jig setup, and then run a few at a time, even just 3 per run. Ill look into it closely, and get you a price thru PM.|
|03-22-2014 04:41 PM|
Machining my D300 bearing retainer per JB Conversion specs for the HD shaft?
|03-15-2014 11:03 AM|
|Arya Ebrahimi||Not an immediate need, but is an adapter shaft within your range of capabilities? Basically blind female splines on one end and a male splined shaft on the other?|
|03-10-2014 09:35 AM|
|This thread has more than 25 replies. Click here to review the whole thread.|