| 05-04-2010 07:20 PM |
| carlito |
This thread has some good information, as you will see the striker plates this guy used are different than the ones I suggested above.
http://www.jeep-cj.com/forums/f7/cj7...el-doors-3926/
|
| 05-04-2010 07:15 PM |
| carlito |
Quote:
Originally Posted by carlito
Same here, i`ll look in to it. My body tub had nothing - no later style strikers or early style. Maybe your stock tub has what is needed - these doors close with an angled bar that slides over a flat striker plate, rather than the round striker pin.
|
Ok my buddy who I got the doors from has these strikers - and they work perfectly, we just test fit the door with these. These are bolted in with two bolts. Same as the pin style striker pods that previous posters have mentioned, except these bolt to the face of the door opening rather than the tub near the roll bar.
http://www.quadratec.com/products/11...googlemerchant
|
| 05-04-2010 07:10 PM |
| carlito |
Quote:
Originally Posted by c_me_roll
do you have the original strikers for the early doors? we might be able to work something out but if i still have to fab a striker for the older doors ill just keep my newer ones.
|
Same here, i`ll look in to it. My body tub had nothing - no later style strikers or early style. Maybe your stock tub has what is needed - these doors close with an angled bar that slides over a flat striker plate, rather than the round striker pin.
|
| 05-04-2010 07:05 PM |
| c_me_roll |
Quote:
Originally Posted by carlito
I`m not too far away from you, i`ll trade my early doors for your wrangler doors. I have an 85 so I could really use the later doors as mine will not latch to my tub, lol. My doors are perfect and not missing anything - but could probably toss in some cash to even it up.
|
do you have the original strikers for the early doors? we might be able to work something out but if i still have to fab a striker for the older doors ill just keep my newer ones.
|
| 05-04-2010 07:04 PM |
| c_me_roll |
Quote:
Originally Posted by Rokcrawlr
|
thnxs but already have those strikers out of the wrangler was looking for something that just bolted up easier w/ less fab work...
|
| 05-02-2010 09:05 PM |
| Mr.N |
Quote:
Originally Posted by LetchcoreCJ
That wont work on an 80 tub..
|
They will not work as is, true.
You could fab up a spacer, or find the piece to tac weld to the body.
|
| 05-02-2010 09:00 PM |
| Rokcrawlr |
Try this http://ep.yimg.com/ca/I/collinsbros_2105_10717204 bolt to the original striker plate. Something like this could be fab'd very easy.
-Troy
|
| 05-01-2010 10:47 PM |
| carlito |
I`m not too far away from you, i`ll trade my early doors for your wrangler doors. I have an 85 so I could really use the later doors as mine will not latch to my tub, lol. My doors are perfect and not missing anything - but could probably toss in some cash to even it up.
|
| 05-01-2010 08:02 PM |
| LetchcoreCJ |
Quote:
Originally Posted by Rokcrawlr
|
That wont work on an 80 tub..
|
| 04-30-2010 06:42 PM |
| Rokcrawlr |
http://www.4wd.com/productdetails.as...=0&partID=8630
|
| 04-30-2010 08:14 AM |
| PumpkinCrusher |
Just put the striker you need. Just a glorified bolt.
|
| 04-29-2010 08:39 PM |
| carlito |
Might be bad advice but I think you can drill in a later striker just fine. I am actually looking for the early style strikers for my early doors. 
|
| 04-29-2010 07:58 PM |
| c_me_roll |
wrangler doors on early cj7 ?
so i got a top from a 90 wrangler w/ full doors for my girls 1980 CJ7 and the strikers dont work with her tub.. is there some easy way to make these work or somewhere to buy strikers that will function properly?sorry for the stupid ? but any help would be greatly appreciated thnx feel free to flame away...
|
Topic Review (Newest First)
