Pirate4x4.Com : 4x4 and Off-Road Forum - Reply to Topic
 
Pirate4x4.Com : 4x4 and Off-Road Forum  

Go Back   Pirate4x4.Com : 4x4 and Off-Road Forum > General Tech > General 4x4 Discussion > Anyone ever tried a 1" bore SE ram?
Notices

Thread: Anyone ever tried a 1" bore SE ram? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Pirate4x4.Com : 4x4 and Off-Road Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.

** A VERIFICATION EMAIL IS SENT TO THIS ADDRESS TO COMPLETE REGISTRATION!! **

Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-01-2012 10:14 AM
TBItoy 1.25" cylinders pop up on surpluscenter.com from time to time for cheap.

They work very good for hydro assist.
05-01-2012 10:05 AM
kidkrawler Where are you guys sourcing a 1.25" ram? Seems like a great in between setup.
05-01-2012 07:18 AM
the glassman i had a 1 1/4 inch bore with 1 in ram cylender on my xj with 44 boggers and stock pump...

not the best but just good enough ..
04-30-2012 05:49 PM
TBItoy There was a guy building a Sag P pump swap bracket that replaced the A/C bracket.

Yunit was the username I think.
04-27-2012 01:59 PM
89lc
Quote:
Originally Posted by ToadRacing View Post
No worries, I was just curious. I've run a TC pump on the 22r but I'd love to go to a p pump as I have a couple of the PSC ones sitting around here. I'm not sure how to build the bracket.

Nikolai
I would imagine that if you used a different length belt, you could fit one pretty easy. Then again, my imagination is off sometimes.
04-27-2012 01:18 PM
ToadRacing
Quote:
Originally Posted by Wilson View Post
Doubtful, it was the rockme single seater. Whatever there was build-wise would be in the toy section. This was 10 yrs ago
No worries, I was just curious. I've run a TC pump on the 22r but I'd love to go to a p pump as I have a couple of the PSC ones sitting around here. I'm not sure how to build the bracket.

Nikolai
04-27-2012 11:00 AM
MT4Runner TC pump on a 22RE is a common swap.

I traded some guy on PBB for his 1.25" ram. Works great on my 4Runner--one-finger steering on the highway, and no lag.
04-27-2012 10:49 AM
Aisin A P style Saginaw is huge. Is there even room under the hood of a Toyota?
04-27-2012 08:22 AM
Wilson
Quote:
Originally Posted by ToadRacing View Post
Do you have any pictures of the bracket for that?

Nikolai
Doubtful, it was the rockme single seater. Whatever there was build-wise would be in the toy section. This was 10 yrs ago
04-27-2012 06:07 AM
Aisin Swap in a Saginaw pump. You'd be lucky to get 700 to 800 psi out of a Toyota pump at idle.
04-27-2012 01:30 AM
iniviate a 1" bore ram would push 864lbs @ 1100psi.

a 1.5" ram would push 1944lbs @ 1100psi.

a 2" ram would push 3456lbs @ 1100psi.

pulling would be less, obviously.
04-27-2012 12:57 AM
ToadRacing
Quote:
Originally Posted by Wilson View Post
Back in the day, we swapped a stock Gm saginaw "p" pump onto a 22r to run hydro
Do you have any pictures of the bracket for that?

Nikolai
04-26-2012 10:09 PM
Wilson Back in the day, we swapped a stock Gm saginaw "p" pump onto a 22r to run hydro
04-26-2012 10:01 PM
TBItoy It'll help, but of course, wont have as much power.

Any reason he wants to keep the stock pump? I assume 22r/re?

A Jeep Cherokee TC Saginaw pump can be swapped on for cheap, and is capable of much more flow and pressure than a Toyota pump.


I'd almost guarantee that the stock Yota pump is not putting out 1200psi. I put a gauge on mine and it would barely make 1000 with the motor revved.
04-26-2012 10:00 PM
Beat95YJ Don't forget to subtract the shaft size.
04-26-2012 09:56 PM
kidkrawler
Anyone ever tried a 1" bore SE ram?

Buddy is building a Harbor Freight/Cal-Ranch sponsored rig, meaning it has been built on a very tight budget. It is all broken in and performing very well but he would like some steering assist.

We have always run 1.5" rams but have noticed with stock pumps a little bit of slow response, he wants to keep his stock pump. We are wondering how a 1" ram would react to a stock yota pump with roughly 1200 psi at idle, probably lower due to it's age. The working pressure of the ram is 1500 psi.

Doing the math the area of a 1 inch ram versus a 1.5 inch ram is almost double the piston size, same as a 1.5 inch to 2 inch. We tried to source a 1.25 inch bore ram for some middle ground but no go.

Searching online I really see no mention of anyone running that small bore of a ram, anyone have an opinion before we order?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -7. The time now is 02:44 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 ©2011, Crawlability, Inc.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.