Pirate4x4.Com : 4x4 and Off-Road Forum - Reply to Topic
 
Pirate4x4.Com : 4x4 and Off-Road Forum  

Go Back   Pirate4x4.Com : 4x4 and Off-Road Forum > General Tech > General 4x4 Discussion > Retubing a 60
Notices

Thread: Retubing a 60 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Pirate4x4.Com : 4x4 and Off-Road Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.

** A VERIFICATION EMAIL IS SENT TO THIS ADDRESS TO COMPLETE REGISTRATION!! **

Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-08-2004 11:20 PM
NE-RokToy well you would only have to retube one side as the long side tube can just be cut down if that helps any.
12-08-2004 10:43 PM
foley or you could go way outside the box, save all that investment in retubing the axle and change t-cases
12-08-2004 10:25 PM
fcfred I asume you are planning on wheeling in Oregon, I would go with 5.13's and the 4.3 v-6 to get a little more poop in the mud with the heavier axle.
you could re-tube the axle, or you could swap it for a low pinion chevy front axle from someone which would save you the time and money of changing it to passenger side drop, but it will also give you a low pinion from a high pinion, slighlty weaker in the front, but nothing I would worry about with a v-6.

I'm pretty sure you have a high pinion, but you need to be sure.

the high pinion is more desirable if:
a you have room, you don't want to have to jack the truck way high to clear the driveshaft
and
you can afford to get it re-tubed or can do it yourself correctly
consider you will need to cut out off the tubes, most likely get at least one new tube-the short side is gonna be really short if you try to stuff it in the axle after you cut it off, get new custom shafts made press the new tubes back in, hope that all this cutting and welding and such doesn't distort the housing

If you want the high pinion I would seriously call some shops and ask them what they would charge to re-tube it for you.

then I would look into the cost of parts for this axle

you may also want to get it made into your new rear axle to get the high pinion, but this then runs the gears on the weak side of the gears.

many things to consider

if you want it fast, easy, and cheap, swap it for a low pinion chevy 60
if you want it as strong as possible, send it to a qualified shop like Dynatrac, and have them re-tube it
if you want to keep the truck light get a dana 44 or a bomber toy axle

it really all depends on what you want to do with the truck tire size, (i know guys running 37s with 44's and very few problems) do you want it wide (cheaper, but hard on tight trails)

good luck
12-08-2004 09:34 PM
91ghostoy I am thinkin 5.13's because I do have dual cases

Should I just cut the third out and start from scratch???
12-08-2004 09:28 PM
coyote HP's can go to 5.38....but get real weak...
12-08-2004 09:10 PM
91ghostoy I also do have a 4.3L that will happen at the same time. I am in the parts gathering stage right now
12-08-2004 09:08 PM
Booger Weldz i believe hi pinions are limited to 5.13's for gearing. fyi, if its going in a toy with a 4banger. i could be wrong(hopefully i am)
12-08-2004 09:02 PM
66CJdean
Quote:
Originally Posted by 91ghostoy
Is it worth the time and effort to turn a driver side dif dana 60 f into a passenger sider diff to fit under my Toy....?
YES
12-08-2004 08:56 PM
91ghostoy
Retubing a 60

I recently got my hands on a dana 60 but the problems are that I want to put it under my toy and the 60 is out of a ford (driver side drop). I know that I would need to cut and lenghten the axle tubes Is it worth the time and effort to turn a driver side diff into a passenger sider diff to fit under my Toy....?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -7. The time now is 12:21 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 ©2011, Crawlability, Inc.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.