|12-22-2017 12:24 PM|
|F*** ROADS||No, they are stock height. aftermarket, stock replacement leafs. They are the 2+1 lighest load capacity spring i could get. Trying to keep it low and soft as possible.|
|12-15-2017 04:44 PM|
|Gozuki||Are those lift springs?|
|12-15-2017 02:52 PM|
|F*** ROADS||Custom u bolt flip. New springs& shocks|
|12-15-2017 02:49 PM|
|F*** ROADS||Fun fact, auto transmissions like to keep fluid on the inside.... for anyone with a 4.6L , can use a cooler from a 5.4L. They are twice as big as the 4.6 ones... so more cooling powa.|
|12-15-2017 02:43 PM|
|F*** ROADS||Code p2106. Throws a different light then the check engine. Truck runs like absolute shit, and un-useable. Plug both sensors in. Restart. bam! Happy as a cucumber!|
|12-15-2017 02:40 PM|
|F*** ROADS||As stated above, the truck will not run properly with the sensors pulled. Regardless if the ABS system is " on" or "off" even having the sensors plugged in, but not bolted to the hub, it will trigger forced limited power. Which makes the truck NOT HAPPY. will not go above 60kmh. So far, the sensors need to be seeing the tone rings while driving, for it to be happy.|
|11-28-2017 06:03 PM|
|Gozuki||What happens if you pull the sensors?|
|11-28-2017 02:40 PM|
|F*** ROADS||The ABS is still disconected via the fuse, ive had it off for years because the system started to act dysfunctional. Technically everything should work as factory, just no intention of fixing the abs at any point. I prefer it wothout. But i can report the truck is still happy as long as the hub wires are conected..|
|11-13-2017 06:25 PM|
|Gozuki||So your ABS is disabled by pulling the fuse, or back to functional?|
|11-08-2017 05:30 PM|
|F*** ROADS||Wow! That is a killer deal! Especially with the new motor, which one? 4.6 or 5.4? Gut the cats and get that thing going! I am happy to update that everything is happy and its driving great! Still have abs fuses pulled, but no codes or faults. Snow happened up here so needed 4x4... got the factory front 150 driveshaft lengthend & got a 1330 to 1350 conversion u joint put in. Been daily driving it for about 3 weeks now. Four wheel has been in the last week.|
|10-26-2017 04:30 PM|
|Stout Fabrication||Today at work we had an '04 crew cab that they decided to pull the plates on because the cats are bad and they don't want to fix it. It has 165,000 miles on it and they just put a rebuilt motor in it 1,500 miles ago. $400 later, I will be driving that sucker home tonight. They put brand new 33" Toyo's on it when they did the motor, so those will offset my cost of the truck when I strip it down and go to one tons and link it. Good to hear about these axles working out so well... Seems like an easy swap, especially if the ABS is happy!!|
|10-25-2017 12:13 PM|
|F*** ROADS||Also, 5125s|
|10-25-2017 11:36 AM|
|F*** ROADS||But so far, all abs sensors are, as i can tell the same. Rear axle is happy, and now, pass side front hub has an f250 abs wire, and driver has an f150 abs sensor bolted to the hub. All plugs are the same. Also tone rings must be identical, because i have had the truck up past 120kmh this weekend. No issues or codes as of now.|
|10-25-2017 11:31 AM|
Lol truly not worked up, just find it funny you seem to care so much... at this point im enjoying wasting your time. I thank all for their input. I respect anyone who doesnt start a post with. Urr weldZz looc liek shit hahalololzz. Anywayyy...
Good news for all. The truck never liked not having the front abs wired hooked up. Already knew this, but was an issue. It would go into limp mode once you went above 80kmh. This is the code that pops up.
|10-25-2017 11:25 AM|
|F*** ROADS||Stock coil buckets, its a bit of both, there is a bit of a bow to them, really not bad though.|
|10-21-2017 06:49 AM|
|10-20-2017 08:35 PM|
I used to work in a shop with 20+ mig welders, I did some time as a welder, but I don't claim to be a "professional" not one of those guys would weld anything over 14g in a straight line.
I also built my whole rig with a 120v mig, with argon, including chopping and rebuilding front and rear frame ends.
Not that any of it matters, OP doesn't want to listen to anyone.
Welcome to pirate cocksucker
|10-20-2017 08:25 PM|
A good hot pass can be done with no weave. It really depends on the welder, the machine, the position, etc. No one size fits all rule here, but I agree with you here, dude should have tied that in a lot better.
|10-20-2017 04:04 PM|
|snowracer||back in post #44 you show the coil buckets and looks the coil have some mad bow to them, is that just the camera angle or are they actually like that? as looks like you are using stock F150 buckets?|
|10-20-2017 03:34 PM|
|10-20-2017 01:17 PM|
I'm not butt hurt, just pointing out the obvious, you seemed to be getting worked up though . You posted on a public forum, if can't handle some criticism, then you might want to try Facebook.
You seriously have no clue about welding, you still need to run a pattern with mig, pretty common knowledge.
|10-20-2017 12:54 PM|
|F*** ROADS||Out of curiosity, did you have any troubles with said welder? Like needing to pre heat, or striking an arc or anything like that?|
|10-20-2017 12:51 PM|
Fucin right ! Lol at the dead nuns
Good to know. Everything welded on this was a miller 220v mig machine. .035 wire
|10-19-2017 03:02 PM|
I've got a little tech again, you can say fuck as well. The only thing that is frowned upon here, and WILL get you banned are racial slurs.
My whole truck was welded with a lincoln 135 plus lol. It's a 110 volt machine, and i did my beadlocks too, no dead nuns as of yet...
|10-19-2017 12:57 PM|
|F*** ROADS||Lol dude, the fack that YOU think they are shit is funny. Stop being so butthurt and move along, you are unwanted. I dont care what 1 person on the internet thinks, stop pushing your " ideas" as fact. MIG is not TIG, no stack of dimes here.. plus, you were not present for the weld, you have no idea on, position, technique, welder used, wire size. Fu** off. You are not ading to the tech on this page. MOVE ALONG PLEB.|
|This thread has more than 25 replies. Click here to review the whole thread.|