 |
|
|
 |
|
|||||||
Topic Review (Newest First)
|
| Yesterday 09:10 AM | |||
| TSwiss | How much for a pair of Dana 60 full float spindle alignment pucks for a 1.5" bar? Can you ship to Canada? PM sent. | ||
| 12-11-2019 10:17 AM | |||
| 66CJdean |
Quote:
Dean |
||
| 12-09-2019 09:43 AM | |||
| 49Marmon | I'm looking to put 2.5 ton Rockwell knuckles on a Dana 80 housing I've seen a post on here somewhere showing a guy in Florida that was doing it. I know your not him but is that a job you do ? I dont have enough posts yet to see your links yet here, is there a website I can go to ? | ||
| 10-09-2019 05:58 PM | |||
| 66CJdean |
That works for me!. I ordered the aluminum for these so it will be here no later than Tuesday so I can get started. Quote:
|
||
| 10-04-2019 11:23 AM | |||
| hamer | Pm sent | ||
| 10-04-2019 08:15 AM | |||
| mcutler1 |
Quote:
 And with the o-ring groove  Matt |
||
| 10-03-2019 04:18 PM | |||
| mcutler1 |
Will do in the AM. Thanks! Sent from my SM-G892A using Tapatalk |
||
| 10-03-2019 04:16 PM | |||
| 66CJdean | The ID of the C's is good so shoot me that number | ||
| 10-03-2019 04:12 PM | |||
| 66CJdean | Can you measure the ID of the unit bearing cups in a few spots and tell me the average so I know what to make the pucks. | ||
| 10-03-2019 05:32 AM | |||
| mcutler1 |
Quote:
Quote:
Sounds good Dean. Let's get this started. parts desired are in the quote above. (I don't need the sterling stuff yet). ADD- housing pucks for 4"x .250 wall, along with the 3.5"x .375w. -KIT, UB pucks, and two pairs of housing pucks. Let me know where to paypal deposit, and lead time. I have two Trail Gear steering UB housings (super duty c's and knuckles) ready for me to build now, and a 14B spindle currie housing (rear) will be here in a couple weeks. Matt CutlerFab 336-401-2830 [email protected] |
||
| 09-27-2019 09:37 AM | |||
| 66CJdean | The 1.5"x84" bar comes in the $475 kit. I have an 03 knuckle here just wish I had an 05+ to get the right fitment. I have a unit bearing to work with so I can deal with it. | ||
| 09-18-2019 05:00 PM | |||
| mcutler1 |
Quote:
- 35sp-9,10,60,70,14 carrier pucks and end pieces-$475 - unit bearing pucks (reversible I assume) to fit both 04d/05u- $100 - housing pucks (say ex. 3.5"x .375 tubing)- $85 pair - is the bar included in there somewhere or do I need to source that? - and i don't have any ub cups at the moment for either size, but i have some old unit bearings of each. Thanks for getting back to me Dean. Matt Sent from my SM-G892A using Tapatalk |
||
| 09-18-2019 04:46 PM | |||
| 66CJdean | Hey CJ5? Your profile is set up to not receive PM's so call me since I can't reply to yours | ||
| 09-18-2019 04:39 PM | |||
| 66CJdean |
Quote:
|
||
| 09-18-2019 04:37 PM | |||
| 66CJdean |
To get the unit bearing jigs right this time can you send me a cup. I will credit you for the shipping and then some. So FF jig kit to do 35 spline 9" carrier/60/70/14 and 60/70/14B ends is $475. I will have to find a LH sterling spindle to make more of them as I sold my last one a few week ago but they are $85 for one. Unit bearing jigs are $100 for the pr and do 04down/05up. For $85 we can make some housing jigs so you can weld on the truss with no ends. Quote:
|
||
| 09-04-2019 05:00 AM | |||
| smp | Carrier jigs and ends for a front Dana 60 to 25446. | ||
| 09-03-2019 04:26 PM | |||
| mcutler1 |
Hi Dean. I'm interested in a bar to work with 9/10" housings and larger, (sterling, 14 bolt), steering and straight applications. What do you have available and recommend. Mostly 3.5 and 4" fabricated housings, unit bearing cups and spindles. Example below  That housing will be the first to be built with spindles. Thanks for your time. Matt Cutler fab 336-401-2830 Sent from my SM-G892A using Tapatalk |
||
| 08-17-2019 01:36 PM | |||
| 66CJdean | They just slide in so you are not stuck with 1.25. | ||
| 08-13-2019 11:40 PM | |||
| Flexy Flatty | Received the bushings today, I’ll try to make it down to my shop tomorrow to press them in. This should be the last piece of the puzzle. | ||
| 08-03-2019 06:15 PM | |||
| Flexy Flatty | Thank you | ||
| 08-03-2019 02:54 PM | |||
| 66CJdean |
Sh!T. I forgot that you are 1.25. OK so I have ordered more and will be here Monday. I can fit them to some pucks here so I know they will fit yours once they get to you. Sorry about that. |
||
| 08-02-2019 10:30 AM | |||
| Flexy Flatty | I received the 60/70/14 spindle jigs yesterday but they’re not bushed for the smaller 1.25 bar, they’re still 1.50. Are the bushings something that you can send me and I can press in or do you need the jigs for fitment? | ||
| 07-29-2019 08:44 PM | |||
| Flexy Flatty |
@66CJdean I really need those jigs, please let me know how far out they are. |
||
| 07-23-2019 11:11 PM | |||
| Flexy Flatty |
Quote:
|
||
| 07-18-2019 10:47 AM | |||
| 66CJdean | No. Forgot to put the 60 jigs in the box, they are still sitting on the shelf. I will get them out the door today, sorry about that. | ||
| This thread has more than 25 replies. Click here to review the whole thread. | |||
