Pirate4x4.Com : 4x4 and Off-Road Forum - Reply to Topic
 
Pirate4x4.Com : 4x4 and Off-Road Forum  

Go Back   Pirate4x4.Com : 4x4 and Off-Road Forum > General Tech > General 4x4 Discussion > 351W tranny/ tcase options for project
Notices

Thread: 351W tranny/ tcase options for project Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Pirate4x4.Com : 4x4 and Off-Road Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.

** A VERIFICATION EMAIL IS SENT TO THIS ADDRESS TO COMPLETE REGISTRATION!! **

Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-30-2007 10:32 PM
rock-rod
Quote:
Originally Posted by biggreentj View Post
ok with that tranny, if i want to run a d300, is there someone out there that makes an adaptor?

or is there something that would be easier?
To run a jeep 300 you don't need an adapter as long as the C6 has an aluminum t-case adapter. The bolt pattern is the same, but the C6 output shaft will have to be machined down to 23 spline and shortened or see if A/A sells a replacement input gear for the 300 that is 31 spline. This little trick also works with the AOD as well. Ford and Jeep share the same 6 bolt round pattern, you just have to get around the spline counts and output shaft length.
03-30-2007 10:24 PM
jrod66 A buddy of mine had a 91 bronco and it had a C6 in it, so you could look at the pan, I know that the C6 and AOD have different pans, try that, as far as junk yard shopping, just look around and find a c6 then find a 205, the combo in a yard will be rare, so good luck.
03-30-2007 09:08 PM
Dusty I vote 700R4. The adapter from the SBF to the 700 isn't too pricey since its just a bellhousing adapter plate and flexplate. Then you can run just about any passenger drop T-case you want, mated to the 700. Check out http://www.700r4inaford.com/

Dusty
03-30-2007 01:50 PM
biggreentj really, damn, always too late.
keep an eye out
03-30-2007 01:15 PM
Tulsachokehold Figures Drew, I just helped a friend load up a C6 Np205 combo onto a trailer 2 days ago. Hell, it was even given away.
03-30-2007 01:03 PM
welndmn An early E40d is complete crap.
Get a C6, from the junk yard its only 80$, and a rebuilt is about 300$.
03-30-2007 12:03 PM
tlspeed1 I would try Advanced Adapters, they might have something
03-30-2007 10:47 AM
biggreentj ok with that tranny, if i want to run a d300, is there someone out there that makes an adaptor?

or is there something that would be easier?
03-29-2007 03:26 PM
biggreentj i remembered i asked the ford guys a few weeks ago, and i was told this is what tranny it would have

Model: E4OD
Type: Electronic Four speed Over Drive
Years:
'90-'96 Bronco,
'89-'98 F-Series
Engines: {300, 302, 351w}, {460}, {7.3L IDI}, {7.3L PSD}, {5.4L}
Display: PRN(D)21 w/ overdrive lockout switch
Pan: 20 bolts
Fluid: Mercon
Ratios:
1st 2.71:1
2nd 1.54:1
3rd 1.00:1
4th 0.71:1
Trans code: E

any options for tcases i can add to that, is it possible to get a 205 or a d300 adaptor for one of those?
03-29-2007 03:00 PM
biggreentj i guess what i need to figure out first, is what tranny that is. thanks guys.

any idea how much i could find a c6 and 205 in a yard?
03-29-2007 02:48 PM
tlspeed1 1986 and up Chevy np205 off of a th400 had the same 6 bolt circular pattern as ford did. You will just have to notch a slot on the other side of the adapter for the shift rail to bolt the chev np 205 to the C6.

You will also have to change the input of the 205 from chevy 32 spline to fords 31 spline, which is a quick swap.

Best bet for low ratio, twin sticks, and passenger drop is to find a Ford C6 with a np203, and build or buy a doubler using a chevy passenger drop np205
03-29-2007 02:23 PM
Tulsachokehold
Quote:
Originally Posted by broncodude_73 View Post
c6 Np 205 i guess chevy if he says itll work
My 90 had a 4aod (?. Overdrive) and a bog warner. This might be what he has as well.

But I do agree with the C6 and NP205 combio. granted the 205 is a monster, but it is twin stickable.
03-29-2007 02:14 PM
broncodude_73 c6 Np 205 i guess chevy if he says itll work
03-29-2007 02:05 PM
Toolmaker You can get a Chevy np205 and put the input gear out of a Ford np205 , you will have to retap the mounting holes to the tranny .
03-29-2007 01:49 PM
biggreentj
351W tranny/ tcase options for project

have 351w from a 94 bronco.

not sure what the tranny and tcase are,
but i need a good combo that will bolt up, that will make it pass drop. any options, prolly need a adaptor, any help would be great.

i want something low, even better if i can get twin sticks out of it.

i am sure i will need an adaptor, but hoping there is an option that wont need it.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -7. The time now is 03:22 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 ©2011, Crawlability, Inc.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.