h233b 1350 u-joint - Pirate4x4.Com : 4x4 and Off-Road Forum
 
Pirate4x4.Com : 4x4 and Off-Road Forum  

Go Back   Pirate4x4.Com : 4x4 and Off-Road Forum > Brand Specific Tech > Nissan
Notices

Reply
 
Share LinkBack Thread Tools Display Modes
Old 07-14-2014, 05:54 PM   #1 (permalink)
Registered User
 
Join Date: Jan 2009
Member # 127190
Posts: 1,191
h233b 1350 u-joint

for anyone running a h233b that wants to run a 1350 u-joint on the axle side here is the spicer part that you would need , just need to get the yoke flange opened up for 2.75" pilot and drill the holes on the companion flange to match the yoke flange . just had on done at my local driveshaft shop and took them only a few hours to do

Northern Drivetrain, LLC: Spicer 3-2-809
penski61 is offline   Reply With Quote Quick reply to this message
Old 07-14-2014, 07:42 PM   #2 (permalink)
Registered User
 
Join Date: May 2009
Member # 136471
Location: NW Oregon
Posts: 1,114
I run their 1310 to H233b flange. Works great!
boardbysled is offline   Reply With Quote Quick reply to this message
Sponsored Links
Old 07-14-2014, 07:46 PM   #3 (permalink)
Registered User
 
Join Date: Jul 2012
Member # 223040
Location: Burnaby, Canada
Posts: 13
I used a Dana Spicer Flange Yoke Series 1350 p/n 3-2-119. I had access to a lathe and managed to open up the flange myself. I then used transfer punches to mark out the holes and then drilled them out. Super easy to do, probably took an hour before I had it back on the truck.
China is offline   Reply With Quote Quick reply to this message
 
Old 07-14-2014, 07:56 PM   #4 (permalink)
Registered User
 
Join Date: Jan 2009
Member # 127190
Posts: 1,191
i looked at that one but the bolt holes didn't line up so i went with the one that did just needed to enlarge the holes to match up to the h233 yoke and open up the pilot . i dont have a lathe but luckily the driveshaft shop did it for free

good to know others have figured it out , i just haven't seen many posts about it so i figured id throw this out there

Last edited by penski61; 07-14-2014 at 08:02 PM.
penski61 is offline   Reply With Quote Quick reply to this message
Old 07-18-2014, 05:52 PM   #5 (permalink)
Registered User
 
Join Date: May 2009
Member # 136471
Location: NW Oregon
Posts: 1,114
The one I purchased bolted right up, no drilling or boring necessary. Worked good with the D300 swap as I have the same u-joint on all my driveshafts.
boardbysled is offline   Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Pirate4x4.Com : 4x4 and Off-Road Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.

** A VERIFICATION EMAIL IS SENT TO THIS ADDRESS TO COMPLETE REGISTRATION!! **

Email Address:
Insurance
Please select your insurance company (Optional)

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 07:50 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 ©2011, Crawlability, Inc.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.