Pirate 4x4 banner

1 - 10 of 10 Posts

·
Registered
Joined
·
3,914 Posts
Discussion Starter #1
I have done alot of lookin around with no evail, I am loking for exact dimensions of an 85 front shaft from the cv end, (IE) BOLT PAATTERN . I do belive it has a 3.665 bolt circle but what are the measurements between bolt holes on the ectangle thanx
 

·
Banned
Joined
·
9,402 Posts
From the All Pro Site:

One set is the standard '84 and later Toyota U-Joint pattern (2.350" X 2.350"), the other is '84 and later CV joint pattern (2.350" X 2.775").

Does anyone know the 83 and early bolt patterns? I know they are the smaller bolts.
 

·
Registered
Joined
·
3,914 Posts
Discussion Starter #5 (Edited)
Thanx alot, dont know how I missed that on there site
the info your asking for is this 81-83 into some 84's
cv bolt pattern is on a 3.575 bolt circle with 8mm hole
with 2.35x2.67
81-83-some 84 pinion flange side 3.340 bolt circle diam. rectangle
with 2.200x2.525 also 81-83 hole diam is .335 an 8mm bolt and the 84 and 85 is .41 for a 10mm bolt
Thanx again
Scott
 

·
Registered
Joined
·
469 Posts
Will a front CV driveshaft out of a 79-83 pickup have the same flange pattern as a 85 rear transfer case and 3rd member???
 

·
Banned
Joined
·
9,402 Posts
I'm working on a project right, now so I will be confirming these myself soon. Does anyone have any of these laying around where they can be re-measured. The dimensions should all be even metric numbers like (56mm) or (64mm) and not stuff like 55.9mm or 64.1mm.

Here is the compiled list so far from this post. Once this info in comfirmed I will add it to the Toyota FAQ.



Toyota Bolt pattern listing:

U-Joint pattern '79 thru '83 (maybe early '84)
3.340"[84.8mm] Bolt Cirlce
2.200"[55.9mm] x 2.525"[64.1mm] Rectangular pattern
(4) holes .335"[8.5mm] Diameter


CV-Joint pattern '79 thru '83 (maybe early '84)
3.575"[90.8mm] Bolt Cirlce
2.350"[59.7mm] x 2.670"[67.8mm] Rectangular pattern
(4) holes .335"[8.5mm] Diameter


U-Joint pattern '84 and later
3.323"[84.4mm] Bolt Circle
2.350"[59.7mm] x 2.350"[59.7mm] Square pattern
(4) holes .413"[10.5mm] Diameter


CV-joint pattern '84 and later
3.636"[92.4mm] Bolt Cirlce
2.350"[59.7mm] x 2.775"[70.5mm] Rectangular pattern
(4) holes .413"[10.5mm] Diameter



Oh and do Tacos have these patterns? If not what year is the first taco? 95-96????
 

·
Registered
Joined
·
3,444 Posts
One thing is my 83' donor case had a square flange on front, not round but it was the larger cv bolt pattern with smaller holes. One way to tell what year case you got. My 94 is round front. I have probably 6 of them I can line up and try to measure thursday. See what I can come up with.
 

·
Registered
Joined
·
9,385 Posts
There are several variations out there. There are at least 3 different '84-up CV bolt patterns out there that I've run across, and I wouldn't be surprised if there were more (IFS, V6, auto, rear 2-piece CV, etc.). They are all very similar though.

I just clamp the one I need on the flange, and drill. Leave room for a couple of extra patterns on there. ;)
 
1 - 10 of 10 Posts
Top