[Dust Puppy]

ok i need to find a 19(stock) or better gas tank for my tj. im not gonna tell u WHY i need it. NO i mean it. shut up leave me alone NOOOOO hehehehe. <IMG SRC="smilies/biggrin.gif" border="0">

any ideas?

 

[Guest]

You know you wanna tell <IMG SRC="smilies/thefinger.gif" border="0"> . I almost boogered mine up last time out. See post on dent pulling... Won't tell you much but...uhhhh, I'm drifting....

 

[Dan-H]

DP you seem to be confused with the tech forum and the "wanted forums" <IMG SRC="smilies/thefinger.gif" border="0">

http://www.pirate4x4.com/cgi-bin/ubb/ultimatebb.cgi?ubb=forum&f=9&SUBMIT=Go
http://forums.jeepsunlimited.com/cgi-bin/ju/forumdisplay.cgi?action=topics&number=5&SUBMIT=Go
http://www.outdoorwire.com/cgi-bin/ultimatebb.cgi?ubb=forum&f=16

 

[Skitzo]

dude, was this your first wheeling trip?? man, i learned after my first trip to skid the gas tank...course by then it was already bashed and the fuel sender hosed at the same time...but a very newbie type of carnage.

 

[nasvik]

Dust Puppy -

I have a 19 gallon stock TJ gas tank for sale. Send me a PM or email if you want it.

Paul
[email protected]

 

[Dust Puppy]

welllllllll ok

like an idiot i decided to adjust my pinion angle when i put my driveshaft back in. i figured just to get me though the weekend w/out vibes until i had time to put the rear axle in. WELLLLL what i didnt notice until it was midnight up in the mountains was that the bolt on my track bar was rubing against the tank. There isnt a hole in it just a deep grove. looking at it i really am not sure how much is left there. for peice of mind i would like to replace the tank but then again $$$ i wouldnt mind just slappin some rtv or something over it and going on. I ended up grinding the bolt down away from the tank so its ok at the moment. My kilby got back from my powdercoater late last week so the grove will be protected.

what do u think. is there anything you guys woiuld reccomend putting on there. I could always just melt some plastic on there... heeeheheh ejust kiddin. i dont want to BLOW UP. <IMG SRC="smilies/biggrin.gif" border="0">

thanks <IMG SRC="smilies/eek.gif" border="0">

 

[Skitzo]

duct tape it!!

 

[Insayn]

Use a propane torch to melt the platic and close the groove...I am kidding...KIDDING! You know some backwoods jeeper may try that. <IMG SRC="smilies/wink.gif" border="0"> <IMG SRC="smilies/biggrin.gif" border="0"> <IMG SRC="smilies/biggrin.gif" border="0">

 

[Skitzo]

hey, hold my beer while i light this torch up...watch this!

 

[1BDYJ]

Napa sells a plastic tank repair kit

 

[Jeepmangled87]

Dude time for a fuel cell in the back hun??? good luck.. <IMG SRC="smilies/smokin.gif" border="0">

 

[Skitzo]

hun??? dude - you guys got sumthin goin??

 

[The Californian]

Originally posted by Skitzo:
<STRONG>hun??? dude - you guys got sumthin goin??</STRONG>

BLAHAHAHA....no, wait....
<IMG SRC="smilies/eek.gif" border="0"> <IMG SRC="smilies/puke.gif" border="0"> <IMG SRC="smilies/puke.gif" border="0"> <IMG SRC="smilies/puke.gif" border="0"> <IMG SRC="smilies/laughing.gif" border="0">

[ 09-10-2001: Message edited by: California Dreamin' ]

 

[BossBuilt]

It's polyethylene thermo plastic and can be thermo welded....Take it to your local body shop or motorcycle shop and see if you can get them to weld it for about $10....no flame is needed...it's done with hot air and filler rod. <IMG SRC="smilies/smile.gif" border="0">