Pirate 4x4 banner

361 - 380 of 431 Posts

·
Trail Tech Fab
Joined
·
609 Posts
Discussion Starter #361
Im looking to mate a np205 to a getrag 5 speed manual. Is this posable do you make an adapter?? Any info will help! Thanks!
It was good talking to you Bobby, let us know if we can help you with anything else.
Regards,
Mike
Trail Tech Fab
860-341-1883
[email protected]
 

·
Registered
Joined
·
1 Posts
Hey building the predator buggy to race the SRRS and need a price and acailability on a clockable adater for the th350 to np 205 or partial sponsor ship on parts if interested thank P
 

·
Trail Tech Fab
Joined
·
609 Posts
Discussion Starter #364
Hey building the predator buggy to race the SRRS and need a price and acailability on a clockable adater for the th350 to np 205 or partial sponsor ship on parts if interested thank P
PM sent, thanks!
 

·
Trail Tech Fab
Joined
·
609 Posts
Discussion Starter #366
I don't think I saw it here, Th400 with 2.5" output to 205
Good morning, The 2.5" Th400 isn't a problem, but we need to know what version NP205 you are looking to mate to. I assume its a 32 spline case, but there are figure 8 or bolt bolt patterns(short and long inputs). Just message us here or feel free to give us a call.
Regards,
Mike
Trail Tech Fab
860-341-1883
 

·
Trail Tech Fab
Joined
·
609 Posts
Discussion Starter #370

·
Registered
Joined
·
459 Posts
I need one of these. I have a large bearing, 29 spline 205 going on an nv4500 and the factory getrag adapter is nonexistent, lol. Clocking will be nice though.

Good morning,



More Pic here
Getrag to 205

This Infinitely Clockable Adapter kit sells for $345 shipped in the USA. All hardware, gaskets, and seals are included. The kit comes unwelded of course. Let us know if you have any other questions.
Regards,
Mike
Trail Tech Fab
860-341-1883
[email protected]
 

·
Trail Tech Fab
Joined
·
609 Posts
Discussion Starter #374
Whats` the price on a TH400 (4.5" output) to a Atlas(d300 bolt pattern) adapter run?
Good Morning,
A TH400 to dana 300 pattern adapter kit 4" long face to face currently sells for $335 shipped in the USA.
Regards,
Mike
 

·
Registered
Joined
·
1 Posts
Mike,
Doing a Chevy Cummins conversion and using a 47re and the Chevy np205 race track. Both units will be upgraded to 29 splines, will the Getrag to 205 be the way to adapt these 2 units?
 

·
Trail Tech Fab
Joined
·
609 Posts
Discussion Starter #376
Mike,
Doing a Chevy Cummins conversion and using a 47re and the Chevy np205 race track. Both units will be upgraded to 29 splines, will the Getrag to 205 be the way to adapt these 2 units?
You'll likely need to remove the rear seal from the back of the transmission, but other than that, the Getrag kit should work out fine. The adapter kit comes with a double lip seal that will do the job of the seal in the back of the trans so there is no issue.

Regards,
Mike
 

·
Trail Tech Fab
Joined
·
609 Posts
Discussion Starter #380
4L80E to Ford NP205, shipped to 16365... thanks

Good Morning, We'll just need to confirm you output shaft on the 4l80e and which version 32 spline input gear you are using on the NP205. Sending PM now.
Thanks,
Mike
Trail Tech Fab
860-341-1883
[email protected]
 
361 - 380 of 431 Posts
Top