[muppetz3]

Well its done. I ended up using a 7/16th pin, because all the 3/8's were to short. Then i had to redrill the holes to make it fit. Then i had to shave one of the bolts so the pin could slide by. But now i think i can take the door off in like 1 min =) But i still have 3 to go and then to test them.

Nick

 

[convertiyota]

Where'd you get those nifty pins from?? <IMG SRC="smilies/biggrin.gif" border="0"> <IMG SRC="smilies/biggrin.gif" border="0">

 

[muppetz3]

A local ACE hardware store. I was happy to see them. I was thinking i was going to have to drill a hole! Worked out nice with them.

Nick

 

[4RnrRick]

I just made some last night. I use a 3/8 grade 5 hex ead cap screw that was 4" long then cut off the threads and cross drilled a hitch pin hole. I couldn't find any 3/8 pins that where long either so that is was I did. I also had to shave down one side of the bolt head so it would slip by also.

 

[deleon87]

orchard supply hardware they are the same ones i used for my spare tire carrier, they are like 3 bucks each. hope i find doors this weekend at pick-n-pull to make my half doors then some pins for quik realese.

 

[miniyota]

thats cool, i was trying to figure out how to do that too!!!
<IMG SRC="smilies/eek.gif" border="0">

 

[mÄrK]

Originally posted by beasttoyota4x4:
<STRONG>thats cool, i was trying to figure out how to do that too!!!
<IMG SRC="smilies/eek.gif" border="0"></STRONG>

and to think I've had a write up on my page for that mod for years... I feel so neglected..

 

[drnut]

Ok i just checked out your site.. Very nice.. but i failed to see anything about quick release door hinges.. maybe you could point them out to me... <IMG SRC="smilies/confused.gif" border="0">

 

[BigDaddy]

Very Nice I used a Bolt that slide in....what a pain in the ass...Looks good, Good idea!

 

[mÄrK]

Originally posted by drnut:
<STRONG>Ok i just checked out your site.. Very nice.. but i failed to see anything about quick release door hinges.. maybe you could point them out to me... <IMG SRC="smilies/confused.gif" border="0"></STRONG>

ok I'll go to it :
"our vehicles"
"specs list"
"custom cut top"
or "half doors" (theres a little link to it in there...
sorry about the confusion, I should label those separate in my specs instead of bunching them in with the cut top. anyway, thanks for looking at my site! and heres the direct link to the doors... http://www.geocities.com/Baja/Trails/3184/topless.html

 

[Greg W]

yup, that's exactly what I did. I posted this pic of mine yesterday.

<IMG width=530 height=398 SRC="http://www.pirate4x4.com/ubb/uploads/myhinge.jpg">
<IMG SRC="smilies/bounce2.gif" border="0">

 

[Allen1532]

I did the same trick to my 4runner. I have had it for at least a year, and it still holds up. Very helpful and time saving.

 

[gonewheelin]

nice...i could use some of those <IMG SRC="smilies/biggrin.gif" border="0">

 

[Lil Uzi]

My quick release doesn't look like that. But I am waiting for the door to fall off on my drive to work. Yeah, I drive it to work, and I do have a job. <IMG SRC="smilies/smile.gif" border="0">

 

[OOP'S]

Originally posted by deleon87:
<STRONG>orchard supply hardware they are the same ones i used for my spare tire carrier, they are like 3 bucks each. hope i find doors this weekend at pick-n-pull to make my half doors then some pins for quik realese.</STRONG>

Good luck on finding doors for a 94 at a P-A-P. There are none in the P-A-P's in my area. I did get a slightly damaged door for $30.00 at TAP, <IMG SRC="smilies/eek.gif" border="0"> <IMG SRC="smilies/eek.gif" border="0"> Can you believe that. Instead of shaving the bolts, my buddy just put the pin it in from the bottom with a washer on top then the clip pin.

[ 08-14-2001: Message edited by: OPP'S ]

 

[Fat 65L]

is their enoug room to just have 2 studs and when you open the door so you could just lift it up to take off.

Rhino

<IMG SRC="smilies/skull.gif" border="0"> <IMG SRC="smilies/skull.gif" border="0"> <IMG SRC="smilies/skull.gif" border="0">

 

[deleon87]

Originally posted by OPP'S:

Good luck on finding doors for a 94 at a P-A-P. There are none in the P-A-P's in my area. I did get a slightly damaged door for $30.00 at TAP, <IMG SRC="smilies/eek.gif" border="0"> <IMG SRC="smilies/eek.gif" border="0"> Can you believe that. Instead of shaving the bolts, my buddy just put the pin it in from the bottom with a washer on top then the clip pin.

[ 08-14-2001: Message edited by: OPP'S ][/QB]

you are right there are non here too <IMG SRC="smilies/frown.gif" border="0"> went to like 4 pick-n-pull's and nothing i think i know where theere might be one but i think he'll want too much for them.